Apeks THE FORCE 2-STAGE, Руководство по эксплуатации

Страница: 36 / 67

The Force™ 2-Stage Operation Manual
36
Revision Date 4/23/2019
5. Troubleshooting
5.1. System Messages
5.1.1. Leak Detect Switch Tripped, when pump stops, check leak detect valve for hydraulic oil. If no
oil is present, press OK. If there is oil present, press OIL FOUND – Follow prompt. See
Diaphragm Rupture Shutdown Alarm in section 5.2.11. and follow steps.
5.1.2. E-stop Reset – Resets the emergency stop when pressed. Make sure E-stop button is backed
out.
5.1.3. Payment due by end of month – Lease payment is due by the first of the month or system will
not run.
5.1.4. Check orifice size . Elevated separator pressure detected. – Separator pressure has
maintained over 400psi for five minutes. Check to make sure the required orifice size is in the
separator and that it is tight. Separator pressures between 400-420psi with the extractor at the
target pressure can be ignored but pressures over 400psi with target pressure not reached
check the following. Prime pump for ten minutes, check/clean check valves on diaphragm
pump, and contact Apeks about other options.
5.1.5. Diaphragm pump pressure switch tripped – See Diaphragm Rupture Shutdown Alarm in
Section 5.2.11.
5.1.6. Monthly code entry required – Lease code for that month needs entered. Go to code entry
screen and enter code.
5.1.7. Pump outlet pressure high – See Diaphragm Compressor Outlet PSI High Alarm in
Section 5.2.8. Check to verify that bottles are open if in recovery.
5.1.8. Separator pressure has risen – Separator pressure is higher than 500psi, separators will be
pumped down or vented.
5.1.9. Low bottle detected at start up – Check that bottle is open and has pressure. Pressure needs
to be above 500psi, change out if necessary.
5.1.10. Machine is in bottle change mode – Change bottle and acknowledge to continue.
5.1.11. Cycle complete or terminated but vessel(s) still pressurized – System is stopped but there
is still pressure over 100psi in one of the vessels. Vent or recover vessels before opening.
5.1.12. Recovery complete – System recovered vessels down to 100psi and vented the extractor.
Open valve 10 and acknowledge the prompt to relieve pressure from the rest of the system.
5.1.13. Check/Replace Bottle – Indicates machine is in bottle change mode.
5.1.14. Extractor Pressure > 2000psi twice in ten minutes – Follow prompt and reset message.
5.1.15. Extractor Pressure not equalizing – see Extractor Not Equalizing Alarm in Section 5.2.13.
5.1.16. Recovering due to low system pressure – Follow prompts and reset message.
5.1.17. Recovery has begun – System has completed its cycle and is recovering CO
2.
5.1.18. CO
2
Low Bottle pressure – Change out bottle to get bottle pressure above 500psi.
5.1.19. Transition to (BA/AB) but Ext (A/B) not ready – Close open extractor and acknowledge on
the elapsed time setting screen to continue.
5.1.20. Sep pressure test failed – Close open separator and acknowledge on the manual screen to
continue.
5.2. System Alarms
5.2.1. Air PSI High/Low Alarm – Air psi is above or below range of acceptable pressure. Decrease
air pressure or check the air compressor and increase pressure.
5.2.2. Chiller 1 Fault/Warning Alarm – Check chiller screen for alarm and consult chiller manual.
5.2.3. Chiller 2 Fault/Warning Alarm – Check chiller screen for alarm and consult chiller manual.