APART PM1122 Скачать руководство пользователя страница 16

16

Pre-amplifier

16. 

 

Mic 1 to 5 phantom switch:

 fl ip down the dipswitch from 

channel 1 to 5 if you want to apply a 20 VDC phantom power 
to input 1 to 5. Don’t use unbalanced sources in combination 
with phantom power turned on on the same channel !

17.  Mic/line 1 to 5 sensitivity knobs:

 turn these knobs to adjust mic/

line 1 to 5 input sensitivity and gain: the signal/clip led present 
on mic/line input 1 to 5 is your guide: turn down the knob to 
the left fi rst, and gradually turn it to the right while you are 
speaking loudly in the mic or while the line signal is applied. 
When the signal/clip led turns red, you are overloading the 
input. Turn the knob to the left a little until the led doesn’t light 
up red anymore. Take your time to preset all mic/line inputs this 
way.

18.  Input 3 to 5 input blocks:

 connect your balanced mic or line 

signals on these euroblock connectors.

19.  Input 1 and 2 input blocks:

 connect your balanced mic or line 

signals on these euroblock connectors. Additionally connect 
the mic 1 and/or mic 2 switch(es) on these blocks to activate 
the chime and priority. These contacts can be used for inputs 
3-5 as well. Please note the priority system; the MIC1 contact 
will mute MIC2-3-4-5 + Music, and the MIC2 contact will mute 
Music (if dipswitch 4 is set).

20. 

 

Ground connector:

 connect your system’s ground or safety 

ground on this connector if this is not already done by 
mounting the unit in a properly grounded rack.

For additional functionality, there are also 2 open collector outputs at the rear controlled 
by the priority switch, one output per zone. They can only be used by qualifi ed 
technicians. Maximum sinkable current per output is 50 mA, maximum voltage is 24VDC. 
No AC voltages are allowed on these outputs ! In case of inductive loads such as relays, 
provide additional measures to avoid damage to the open collector outputs.

Содержание PM1122

























Отзывы: