AP Cumberland Feed-Link 2 Скачать руководство пользователя | Manualshive

Страница: 28 / 46

background image

7. Networking

28

PNEG-2340

Feed-Link 2

Connecting the RS485 Network Cables to the Network Master

Use 18 AWG shielded, two conductor RS485 cable from RS485 out cable on the display unit, connect
white wire to terminal marked “A” on back of the Network Master. Connect the black wire to the terminal
marked “B” on back of the Network Master. Connect GND (shield) wire to the terminal marked “shield” on
back of the Network Master.

If the Network Master is located in the middle of a daisy chain network, there will need to be an additional
RS485 in cable connected to the back of the Network Master. It should be connected the same as the
RS485 out cable above.

(See Figure 7G.)

Figure 7G Network Master and Display Unit Wiring Diagram

«
...
26
27
28
29
30
...
»

Содержание Cumberland Feed-Link 2















































Отзывы:

Нет отзывов

Похожие инструкции для Cumberland Feed-Link 2

ClubSport Wheel Base V2

Бренд: FANATEC Страницы: 39

Бренд: Hansen Страницы: 4

Smart-MPPT Li Series

Бренд: Y-Solar Страницы: 6

Бренд: Panasonic Страницы: 16

Бренд: Value Point Страницы: 7

Бренд: HandyTrac Страницы: 14

Бренд: TA Страницы: 6

Бренд: Eaton Страницы: 2

Бренд: ZKTeco Страницы: 20

Бренд: ZKTeco Страницы: 8

Бренд: ZKTeco Страницы: 10

Бренд: ZKTeco Страницы: 121

Бренд: ZKTeco Страницы: 12

Бренд: ZKTeco Страницы: 6

Бренд: ZiLOG Страницы: 12

SensoTimer ST6 Duo eco!ogic

Бренд: Kärcher Страницы: 96

Бренд: IBCcontrol Страницы: 16

ArmorBlock 1732E-16CFGM12R

Бренд: Allen-Bradley Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды