AOpen






MX3W-E2, Простое руководство по установке

Страница: 3 / 8

1.
Pull up the CPU socket lever and up to
90-degree angle.
2.
Locate Pin 1 in the socket and look for a
(golden) cut edge on the CPU upper interface.
Match Pin 1 and cut edge. Then insert the
CPU into the socket.
3.
Press down the CPU socket lever and finish
CPU installation.
Plug in the CPU fan cable to the 3-pin CPU FAN connector. If you have chassis fan,
you can also plug it on FAN2 or FAN3 (without H/W monitoring) connector. Please note
that MX3W-SC doesn’t have hardware monitoring function; therefore, there is no
sensor pin on CPU fan connector.
5. Setting CPU Voltage & Frequency
4. Installing CPU & Housing Fan
3. Installing CPU
Note: If you do not match the CPU
socket Pin 1 and CPU cut edge well,
you may damage the CPU.
CPU socket lever
CPU Pin 1 and cut edge
GND
Note: Some CPU fans do not have
sensor pin, so that they cannot
support fan monitoring.
CPU Fan Connector
FAN3 Connector
Setting CPU Core Voltage
This motherboard supports CPU VID function. The CPU core voltage will be automatically
detected and the range is from 1.3V to 3.5V. It is not necessary to set CPU Core Voltage.
Setting CPU Frequency
This motherboard is CPU jumper-less design, you can set CPU frequency through the
BIOS setup, and no jumpers or switches are needed.
Core Frequency = CPU FSB Clock * CPU Ratio
CPU Ratio 2x, 2.5x, 3x, 3.5x, 4x, 4.5x, 5x, 5.5x, 6x, 6.5x, 7x, 7.5x, and 8x
CPU FSB (By BIOS table) 66.6, 66.8, 68.3, 75.3, 78, 80, 95, 100, 100.2, 105, 110, 114, 117, 122, 127, 133.3,
133.6, 138, 140, 144, 146.6, 150, 157.3, 160, 166MHz.
CPU FSB 66~166MHz
CPU CPU Core Frequency FSB Clock Ratio
Celeron 300A 300MHz 66MHz 4.5x
Celeron 366 366MHz 66MHz 5.5x
Celeron 366 366MHz 66MHz 5.5x
Celeron 400 400MHz 66MHz 6x
Celeron 433 433MHz 66MHz 6.5
Celeron 466 466MHz 66MHz 7x
Celeron 500 500MHz 66MHz 7.5x
Celeron 533 533MHz 66MHz 8x
Celeron 566 566MHz 66MHz 8.5x
Celeron 600 600MHz 66MHz 9x
Pentium III 600E 600MHz 100MHz 6x
Pentium III 650E 650MHz 100MHz 6.5x
Pentium III 700E 700MHz 100MHz 7x
Pentium III 750E 750MHz 100MHz 7.5
Pentium III 800E 800MHz 100MHz 8x
Pentium III 850E 850MHz 100MHz 8.5x
Pentium III 533EB 533MHz 133MHz 4x
Pentium III 600EB 600MHz 133MHz 4.5x
Pentium III 667EB 667MHz 133MHz 5x
Pentium III 733EB 733MHz 133MHz 5.5
Pentium III 800EB 800MHz 133MHz 6x
Pentium III 866EB 866MHz 133MHz 6.5
Pentium III 933EB 933MHz 133MHz 7x
Pentium III 1000EB 1GHz 133MHz 7.5x
Tip: If your system hangs or fails to boot because
of overclocking, simply use <Home> key to restore
the default setting (433MHz).
Warning: Intel
®
i810
chipset supports maximum
133MHz FSB and 66MHz
AGP clock, higher clock
setting may cause serious
system damage. Please
note that the 810 chipset
on MX3W-V2 can only
support maximum 100MHz
FSB.
FAN2 Connector
SENSOR
+12V