Antunes GST-3V Скачать руководство пользователя страница 6

Страница: 6 / 24

GST-3V BUN TOASTER

P/N 1012002 Rev. B 04/18

Operating Instructions

The GST-3V toasts Crowns, Heels, Clubs, and other

products. Follow these steps to start the GST-3V:

1. Turn on the toaster and wait for warm-up to com-

plete.

2. Set the Compression Knob to 4 (recommended).

If further adjustments are required see page 8

under Adjusting Toast Quality. Refer to the figure

on page 7.

3. When the unit reaches operating temperature, the

control panel displays “Ready”.

4. Insert product into the designated area of the Bun

Feeder Assembly with the cut side of the bun fac-

ing towards the front. Toasted product drops into

the Bun Buffer.

OPERATION

Figure 2. GST-3V Control Panel and Display

User Mode

User Mode allows an operator to view the toaster set-

tings but does not permit any adjustments.

1. Press and hold the

PROGRAM

button for 5 sec-

onds. After 5 seconds, the display will show the

actual temperature of the Rear Platen.

2. Press the

LIGHTER

button to toggle between

the setpoint and actual temperature of the Rear

Platen Heater.

3. Press the

PROGRAM

button to proceed to the

Front Platen Heater menu. The display shows the

actual temperature of the Front Platen.

4. Press the

LIGHTER

button to toggle between

the setpoint and actual temperature of the Front

Platen.

5. Press the

PROGRAM

button to proceed to the

Motor Menu. The display shows the actual speed

of the motor.

6. Press the

LIGHTER

button to toggle between the

setpoint and actual speed of the Motor.

NOTE: The unit will exit User Mode after 5 seconds

of keypad inactivity.

Manager Mode

Manager Mode allows an operator to view and adjust

the following settings:

•

Platen A Temperature

•

Platen B Temperature

•

Motor Speed

•

Temperature Units (Celsius or Fahrenheit)

•

Current Selection: 208 or 240 volts

Manager Mode also allows an operator to view (but

not adjust) the Ambient Temperature of the Control

Compartment as well as the number of days of opera-

tion.

1. Turn the unit off.
2. Turn the power on while holding the

PROGRAM

button. Hold the button for 5 seconds until the dis-

play shows “EnA.” Release the button.

3. To adjust the Platen Setpoint Temperature, press

the

LIGHTER

DARKER

buttons to reach the

desired temperature.

NOTE: The recommended temperature setting for

the Rear Platen is 257° C (495° F).

Содержание GST-3V

























Результаты поиска

Содержание GST-3V

Отзывы:

Похожие инструкции для GST-3V

Бренды по названию

Популярные бренды

Antunes GST-3V, Руководство пользователя

Результаты поиска

Содержание GST-3V

Отзывы:

Похожие инструкции для GST-3V

Бренды по названию

Популярные бренды