Antunes 9210912 Скачать руководство пользователя страница 7

Страница: 7 / 20

Bun Chute

Temperature Controls

& Temperature Display

Butter Wheel

and Pan

Bun Thickness

Adjustment Control

(Crown)

Bun Thickness

Adjustment

Control (Heel)

Hi-Limit

Reset

Power

Cord

Figure 3.

VCTM-2 Toaster

Operation

Set the Bun Thickness Adjustment

Controls (Figure 3).

NOTE:

The McDonald’s “Gold

Standard” for toasting is the

deciding factor on the finished

product, not the Bun Thickness

setting.

NOTE:

The default Bun Thickness

settings are 2 for Crown Front

and 2 for Heel Rear, but settings

are adjustable from 1-6. It is

acceptable to adjust the Bun

Thickness setting as needed

to achieve the desired quality

toast and bun compression.

Turn the power on and wait until the

display reads USE before proceeding.

NOTE:

The display (Figure 3) flashes

“LO” during warm-up. “USE”

appears when the toaster is

ready for use.

Fill the Butter Pan.

Slide buns across the rotating Butter

Wheel with the cut face down. Drop

buns into the Bun Feeder. Insert buns

so they face the center platen. The

cut sides of heel and crown must

face each other and slide against the

Release Sheet with Crowns inserted

in the front and Heels inserted in the

rear.

Toasted buns drop onto the Bun

Chute (Figure 3).

Test at least 4 buns before putting the

toaster into service.

Default Settings

Recommended temperatures

The default and recommended

temperature setting for the A platen

heater is 485° F (252° C).

The default and recommended

temperature setting for the B Platen

heater is 495° F (257° C).

Recommended Speed Setting

The default and recommended speed

setting is 140 for 40 second pass-through

(plus or minus 2 seconds).

Light/Dark Setting

The toaster has a Light/Dark adjustment

setting that allows you to adjust the toast

quality as the toaster is running.
While the toaster is in USE mode, press

the UP or Down arrow buttons to adjust the

Light/Dark setting.
The default setting is D0.
Light 10 is the lightest setting
Dark 10 is the darkest setting.

P/N 1011376 Rev. D 11/20

Содержание 9210912





















Результаты поиска

Содержание 9210912

Отзывы:

Похожие инструкции для 9210912

Бренды по названию

Популярные бренды

Antunes 9210912, Руководство пользователя

Результаты поиска

Содержание 9210912

Отзывы:

Похожие инструкции для 9210912

Бренды по названию

Популярные бренды