ANthony AST-1500 страница 28 Скачать руководство пользователя

Страница: 28 / 36

Anthony Lifgtates, Inc.

AST, AST-L, and AST-PLUS Models

www.anthonyliftgates.com

800-482-0003

1 — A-131017

A-131017

2 — A-131028

A-131028

3 — A-131034

CAUTION SECURE LATCH WHILE IN TRANSIT.

A-131034

4 — A-131115

PERSONAL INJURY HAZARD

Operation may require user to stand on platform.

To prevent injury or death of operators or bystanders:

Read and follow operator/owner manual for safety,
operation, inspection, and maintenance instructions.

•

Do not place unstable or unsafe loads on platform.

•

Do not allow loads to extend over edge of platform.

•

Be aware of surroundings when operating liftgate.

•

Owner/operators must properly maintain liftgate.

•

Ensure footing is stable and stand away from edge
before raising or lowering platform.

•

Do not exceed capacity or use liftgate for anything
other than intended purpose.

•

Do not allow body parts to contact moving components.

•

WARNING

A-131115

5 — A-131134

This hydraulic reservoir is

filled with Dextron ATF

hydraulic fluid. Use ONLY the

same or equivalent fluid.

A-131134

6 — A-150238

NOTICE

THIS LIFTGATE IS PROTECTED

WITH AN ELECTRICAL OVERLOAD

CIRCUIT PROTECTION DEVICE,

EITHER A CIRCUIT BREAKER, OR

A FUSE, AND IS LOCATED NEAR

THE POWER SUPPLY

A-150238

Содержание AST-1500





































Результаты поиска

Содержание AST-1500

Отзывы:

Похожие инструкции для AST-1500

Бренды по названию

Популярные бренды

ANthony AST-1500, Руководство по установке

Результаты поиска

Содержание AST-1500

Отзывы:

Похожие инструкции для AST-1500

Бренды по названию

Популярные бренды