Anthem Statement D2 Скачать руководство пользователя страница 36

Страница: 36 / 102

SETUP

continued …

Procedure for adjusting Room Resonance Filter:

• Enter the setup menu. Go to SPEAKER CONFIGURATION and press

SELECT

• Press the

button until you reach ROOM RESONANCE FILTER and press

SELECT

• Use the

buttons to set TEST TONE to Auto. Press

SELECT

to start automatic sweeping of the

test tones. Alternatively, you can set TEST TONE to Manual – to vary the frequency, press the

buttons to reach TEST FREQ, then use the

buttons to change frequency.

• Some subwoofers are not able to accurately reproduce frequencies below 30 Hz or so, especially

at higher levels. In addition, it can be quite difficult to hear these frequencies. If playing them
causes unusual sounds indicating the subwoofer is being stressed, do not continue to play them.

• TEST FREQ changes to show the frequency being played during automatic sweep. Listen for (or

measure) the frequency that sounds too loud compared to the other frequencies.

• Press the

button until you reach CENTER FREQ and select the frequency that is closest to the

test tone frequency that was found to be the loudest.

• Press the

button until you reach APPLY FILTER and set it to Yes.

• Press the

buttons to go to FILTER DEPTH and FILTER WIDTH. Adjust both to achieve the flattest

response across the range of test tones.

• Press

BACK

to stop the test tones and leave this submenu.

Содержание Statement D2







































































































Результаты поиска

Содержание Statement D2

Отзывы:

Бренды по названию

Популярные бренды

Anthem Statement D2, Руководство по эксплуатации

Результаты поиска

Содержание Statement D2

Отзывы:

Бренды по названию

Популярные бренды