Anthem Statement D2 Скачать руководство пользователя страница 29

Страница: 29 / 102

3.2

SET TIME / TIMERS

The time and day, plus 6 different timers are set in this menu. The timers in the processor are like an alarm
clock, but allow two different timer settings for each of MAIN, ZONE2, and ZONE3.

To set Time and Day:

• Enter the setup menu. Go to SET TIME / TIMERS and press

SELECT

• Press the

button until you reach FORMAT.

• Use the

buttons and choose 12 Hr or 24 Hr.

• Press the

button to go to TIME.

• Press

SELECT

. “12” or the current hour will be highlighted in red.

• Use the Master Control Knob or the

buttons to set the current hour.

• Press the

button. “00” or the current minutes will be highlighted.

• Use the Master Control Knob or the

buttons to set current minutes.

• Press

BACK

to return to the menu line.

• Press the

button to go to DAY then use the

buttons to set the current day.

All Timers:

This allows you to simultaneously “Enable” or “Disable” all Timers for MAIN, ZONE2, and ZONE3.

Highlighting SET MAIN TIMERS then pressing

SELECT

displays this menu:

2. SET TIME / TIMERS

a. FORMAT: 12 Hr

TIME: 12:00 AM

DAY: Sunday

d. ALL TIMERS: Disabled

e. SET MAIN TIMERS

f. SET ZONE2 TIMERS

g. SET ZONE3 TIMERS

2e. SET MAIN TIMERS

a. --- TIMER 1: Off ---

b. WEEKDAY ON: 8:00 AM

c. WEEKDAY OFF: 11:00 PM

d. WEEKEND ON: 10:00 AM

e. WEEKEND OFF: 11:00 PM

SOURCE: Last Stn

ON-VOLUME: -35.0 dB

h. --- TIMER 2: Off ---

i. WEEKDAY ON: 8:00 AM

j. WEEKDAY OFF: 11:00 PM

k. WEEKEND ON: 10:00 AM

l. WEEKEND OFF: 11:00 PM

SOURCE: Last Stn

ON-VOLUME: -35.0 dB

SETUP

continued …

Содержание Statement D2







































































































Результаты поиска

Содержание Statement D2

Отзывы:

Бренды по названию

Популярные бренды

Anthem Statement D2, Руководство по эксплуатации

Результаты поиска

Содержание Statement D2

Отзывы:

Бренды по названию

Популярные бренды