Quick Start Assembly/Installation Instructions
Before beginning assembly, make sure all parts needed are present.
Coaxial cable sold separately.
1
2
2
3
3
4
5
5
8
8
8
6
6
7
7
7
9
11
10
10
To locate the broadcast towers in your area, go to
antennapoint.com and enter your zip code, or scan the
QR code.
Point the front of the antenna in the direction of your TV stations' broadcast towers
and check reception by scanning for channels. If you are not receiving all of the
available channels, move the antenna and rescan.
Follow the instructions in the owner's manual of your TV or converter box to change
the settings from ‘CABLE’ to ‘ANTENNA’, ‘AIR’, or ‘BROADCAST’.
Follow the instructions in the owner's manual of your TV or converter box to
change the input from ‘CABLE’ to ‘ANTENNA’, ‘AIR’, or ‘BROADCAST’.
INDOOR INSTALLATION
FRONT VIEW
Call to Learn.
Toll-Free Helpline:
1-877-825-5572
Raise dipoles
until they click
into place.
Raise dipoles
until they click
into place.
Point the front of the antenna in the direction of your TV stations' broadcast towers
and check reception by scanning for channels. If you are not receiving all of the
available channels, move the antenna and rescan.
To add the
mounting
hardware,
you must
first remove
the long bolt.
Next, follow the
illustrations to
attach the
mounting
hardware to the
antenna.
HELPFUL TIP:
IT'S IMPORTANT TO CHECK THE RECEPTION IN THE
LOCATION WHERE YOU INTEND TO INSTALL THE ANTENNA, PRIOR TO
ATTACHING THE J-MOUNT MAST TO ANY SURFACE.
Before installing the antenna on the J-Mount Mast
(3)
, adjust
the mast, so it is in a vertical position. You will need to adjust
the antenna after it is mounted for the best reception.
Install the antenna
on the J-Mount
Mast
(3)
by
positioning the Mast
Clamp
(6)
around
the mast. Tighten
the Wing Nuts
(7)
to
secure the antenna
to the mast.
J-MOUNT INSTALLATION
Attach the J-Mount Mast
(3)
to the Mount Base
(10)
with
the Hex Bolts and Nuts
(8)
,
as shown above.
Mark the Mount Base
(10)
position on the desired surface
and drill pilot holes, 1" deep, for each of the 50mm
J-Mount Bolts
(9)
.
Place the Sealing Pads
(11)
over the pilot holes, and the
Mount Base
(10)
on top of the Sealing Pads.
Tighten the J-Mount Bolts
(9)
to secure the base to the
surface.
OUTDOOR INSTALLATION
Technical Assistance is available
Monday – Friday, 9:00 am to 9:00 pm
and Saturday – Sunday, 10:00 am to 6:00 pm, Central Time.
Required: Coaxial Cable
(sold separately)
, Adjustable Wrench, Power Drill, 3/16" Drill Bit,
8 and 10mm Ratcheting Drivers, and a #2 Phillips Screwdriver
4
The ClearStream 2MAX™ comes with:
1)
ClearStream 2MAX™ Antenna
2)
Indoor Antenna Stand
3)
J-Mount Mast
4)
Mast End Cap
5)
1 - 25mm Mast Clamp Bolt
6)
Mast Clamp and Back Plate
7)
Wing Nuts and U-Clamp
8)
2 - 40mm Hex Bolts and Nuts
9)
4 - 50mm J-Mount Bolts
10)
Mount Base
11)
4 - Sealing Pads
Connect coaxial cable
(sold separately)
to the
antenna prior to inserting
the cable into the
Antenna Stand
(2)
.
9
11
10
WALL MOUNT
Connect the antenna to the TV or converter box and run a full channel scan. If reception is not as desired, move the antenna and rescan for the available channels.
Before permanently attaching the antenna to any surface, TEST
RECEPTION in that area.
Use the long bolt, removed
from the spine in the
previous step, and the Mast
Clamp Bolt
(5)
to secure the
Back Plate
(6)
.
CLEARSTREAM 2MAX™
