5
Z-20:
1. LCD-Display
2. FUNCTION-Button
3. UP-/DOWN-Button
4. TIMER-Button
5. VOLUME-Button
6. MANUAL-Button
1. Via
the
FUNCTION
Button, you can adjust the desired settings. Pressing the FUNCTION Button will cycle
through different options including Volume, Timer, Heat & Fan. The
ENTER (VOLUME)
Button is used to
select the desired option. To adjust fog output volume setting, simply go into VOLUME option. Adjust the
volume percentage (within the range of 1% to non-stop burst) by means of UP/DOWN Buttons. To adjust timer
setting, go into TIMER option. Cycle through Interval (within the range of 1 to 900 seconds), Duration (within
the range of 1 to 200 seconds), and Volume (within the range of 1% to non-stop burst) by means of UP/DOWN
Buttons. Use ENTER (Volume) Button to select each option and make changes as desired. To turn OFF the
heater and fan, go into Heat & Fan option. Use ENTER(Volume) Button to confirm the selection. Use
ON/OFF
(MANUAL)
Button to turn it ON.
2. Always
press
ENTER (VOLUME)
Button to confirm setting.
3. Press
ESC (TIMER)
Button to exit current menu level and move to an upper (previous) level.
4. Press
TIMER
Button to activate the timer function. The display shows the adjusted interval and the device
counts the seconds down to “
O
“. After that, the fog emission is triggered at the volume adjusted under “ Timer
Option“. The duration depends on the settings adjusted under “Duration“. If you wish to deactivate the timer
function, press the Timer Button once more.
5. Press
the
VOLUME
Button for immediate triggering of the fog emission at the volume adjusted under
“Volume“ Option. Press the VOLUME Button once more in order to stop the fog emission.
6. Press
the
MANUAL
Button for immediate triggering of the fog emission at 100% volume. Let the MANUAL
Button loose in order to stop the fog emission.
7. When
in
Standby mode
, press
ON/OFF
Button to reactivate the machine.
♦
Z-30:
All the Z-20 features plus wireless capability. Wireless operation is possible up to a distance of 50
meters. The address can be set from 0 to 8, which means a max. 9 different units can be controlled separately
or in any combination desired. Press FUNCTION to cycle to RF mode to select desired address number. Make
sure the address setting on the Z-30 matches the address setting on the transmitter. There are two buttons on
the transmitter. The
blue
one is to emit fog and
red
one is to stop the operation.
Performance Note
♦
All fog machines develop condensation around the output nozzle. Because this may result in some moisture
accumulation on the surface below the output nozzle, consider this condensation when installing your unit.
♦
All fog machines may sputter small amounts of fog occasionally during operation and for a minute or so after
being turned off.
♦
All fog machines have a recycling period after long bursts when the machine will shut itself down for a short
period in order to heat up again. During this time no fog can be produced.
Maintenance
6
Do not allow the fog liquid to become contaminated. Always replace the caps on the fog liquid container and the
fog machine liquid tank immediately after filling. After every 40 hours of continuous operation, it is recommended to
run a cleaning solution composed of 80% distilled water and 20% white vinegar through the system to prevent the
accumulation of particulate matter in the heating element.
The recommended cleaning regimen is as follows:
1.
Empty all fog liquid from machine. Add cleaning solution to tank. Plug unit in and begin warm up.
2.
Run unit in a well-ventilated area until tank is almost empty. Do not allow the pump to run dry.
3.
Replace nozzle.
4.
Cleaning is now complete. Refill with fog liquid. Run the machine briefly to clear any cleaning solution from the
pump and heater.
5.
Do not operate the fog machine without liquid at any time.
Note:
All fog machines are prone to clogging due to the thick consistency of fog liquid and the high temperature at
which it vaporizes. However, a properly maintained fog machine should provide years of reliable use.
Clean with a dry cloth only. Store dry.
Cleaning your fog machine regularly will help reduce costly replacement and repair charges.
Storage
When storing, run distilled water (not tap water) through the system as described in the cleaning regimen above.
This will help avoid any particles condensing inside the pump or heater.
Please read and save these instructions.
