ANTAIRA LNX-0702C-SFP Series Скачать руководство пользователя

Страница: 22 / 23

Antaira Industrial Ethernet Switches

LNX-0702C-SFP Series User Manual V1.1

7. Technical Specifications

Table 7.1 has the technical specifications for Antaira’s LNX-0702C-SFP series: 7-port industrial

gigabit unmanaged Ethernet switch with 5*10/100Tx and 2*100/1000 SFP slots.

Standards

IEEE 802.3 10BaseT Ethernet

IEEE 802.3u 100BaseTX fast Ethernet

IEEE 802.3z gigabit Fiber

Protocol

CSMA/CD

Transfer Rate

14,880pps for Ethernet port

148,800pps for fast Ethernet port

Transmission Distance

Up to 100M (Fast Ethernet)

Transmission Speed

Up to 1000Mbps

MAC Address

8K table size

RJ45 (Ethernet) Port

5*10/100Tx auto negotiation speed, full/half duplex

mode, and auto MDI/MDI-X connection

SFP Slot

2*SFP slots; supports dual rate 100/1000

LED

Power Unit: P1 (Green), P2 (Green),Fault(Red)

Ethernet Port: Link/Active(Green), 10/100Mbps

SFP: Link/Active(Green)

Network Cable

10BaseT: 2-pair UTP/STP Cat. 3, 4, 5 cable

EIA/TIA-568 100-ohm (100m)

100BaseTX: 2-pair UTP/STP Cat. 5 cable

EIA/TIA-568 100-ohm (100m)

Over Current Protection

Single-blown fuse

Power Input

Redundant power DC 12~48V with connective

1*6-pin removable terminal block

Fault Output

1 relay output

Max Power Consumption

6.0 Watts

Installation

DIN-Rail mounting, wall mounting (optional)

Operating Temperature

Standard: -10

C to 70

C (14° to 158° F)

EOT: -40

C to 75

C (-40° to 167° F)

Operating Humidity

5% to 95% (Non-Condensing)

Содержание LNX-0702C-SFP Series
























Результаты поиска

Содержание LNX-0702C-SFP Series

Отзывы:

Похожие инструкции для LNX-0702C-SFP Series

Бренды по названию

Популярные бренды

ANTAIRA LNX-0702C-SFP Series, Руководство пользователя

Результаты поиска

Содержание LNX-0702C-SFP Series

Отзывы:

Похожие инструкции для LNX-0702C-SFP Series

Бренды по названию

Популярные бренды