ANTAIRA LNX-0702C-SFP Series Скачать руководство пользователя

Страница: 21 / 23

Antaira Industrial Ethernet Switches

LNX-0702C-SFP Series User Manual V1.1

6. Trouble Shooting



Verify you have the right power cord or adapter. Never use a power supply or adapter with

a non-compliant DC output voltage or it will burn the equipment.



Select the proper UTP or STP cable in order to construct the network. Use an unshielded

twisted-pair (UTP) or shield twisted-pair (STP) cable for RJ-45 connections: 100Ω

Category 5e for 10M/100Mbps. Also be sure that the length of any twisted-pair connection

does not exceed 100 meters (328 feet).



Diagnosing LED Indicators: To assist in identifying problems, the switch can be easily

monitored with the LED indicators which help to identity if any problems exist.

Please refer to the LED Indicators section for LED light indication.



If the power indicator LED does not turn on when the power cord is plugged in, the user

may have a problem with the power cord. Check for loose power connections, power

losses or surges at the power outlet.

Please contact Antaira for technical support service, if the problem still

cannot be resolved.



If the industrial switch LED indicators are normal and the connected cables are correct but

the packets still cannot transmit, please check the system’s Ethernet devices’ configuration

or status.

Содержание LNX-0702C-SFP Series
























Результаты поиска

Содержание LNX-0702C-SFP Series

Отзывы:

Похожие инструкции для LNX-0702C-SFP Series

Бренды по названию

Популярные бренды

ANTAIRA LNX-0702C-SFP Series, Руководство пользователя

Результаты поиска

Содержание LNX-0702C-SFP Series

Отзывы:

Похожие инструкции для LNX-0702C-SFP Series

Бренды по названию

Популярные бренды