ANTAIRA LNX-0601G-SFP Скачать руководство пользователя страница 23

Страница: 23 / 23

Antaira Industrial Ethernet Switches

LNX-0601G-SFP Series User Manual V1.2

EMI

FCC Class A

CE EN61000-4-2,3,4,5,6,8,11,12

CE EN61000-6-2

CE EN61000-6-4

Stability Testing

IEC60068-2-32 (Free fall)

IEC60068-2-27 (Shock)

IEC60068-2-6 (Vibration)

Safety

FCC, CE, UL 61010-1, UL 61010-2-201

UL Class 1 Division 2, ISA 12.12.01

Table 7.1

LNX-0601G-SFP Series Technical Specification

Antaira Customer Service and Support

(Antaira US Headquarter) + 844-268-2472

(Antaira Europe Office) + 48-22-862-88-81

(Antaira Asia Office) + 886-2-2218-9733

Please report any problems to Antaira:

www.antaira.com

[email protected]

www.antaira.eu

[email protected]

www.antaira.com.tw

[email protected]

Any changes to this material will be announced on the Antaira website.

Содержание LNX-0601G-SFP
























Результаты поиска

Содержание LNX-0601G-SFP

Отзывы:

Похожие инструкции для LNX-0601G-SFP

Бренды по названию

Популярные бренды

ANTAIRA LNX-0601G-SFP, Руководство пользователя

Результаты поиска

Содержание LNX-0601G-SFP

Отзывы:

Похожие инструкции для LNX-0601G-SFP

Бренды по названию

Популярные бренды