Anritsu Site Master S251A Скачать руководство пользователя страница 12

Страница: 12 / 16

NOTE

Take care to not lose the Mylar pad
under Q5.

13.

Remove the two hex standoff screws and
nuts holding the serial interface connector to
the test port panel.

14.

Using a 5/16 wrench, loosen the SMA connec-
tors for the Refl and Trans test ports and re-
move the test port panel.

NOTE

If the Power Monitor (Option 5) is in-
stalled, remove the two screws hold-
ing the Power Monitor PCB assembly
to the test port panel and lift it clear
of the connector on the main RF PCB
assembly.

15.

Reverse the above procedure to install the re-
placement RF PCB assembly.

16. REPLACEABLE PARTS

Part Number

Description

Qty

Accessories

10580-00016

User's Guide, Site Master
S120A, S235A, S250A

10580-00020

User's Guide, Site Master
S251A

10580-00007

Battery Replacement and
Disposal Guide

2300-211

Software Tools, Site Master

40-115

Power Supply

SM/STS

Connector, RF Short, N Male

SM/PL

Connector, RF Termination

806-62

Cable Assy, Cig Plug, Female

800-441

Serial Interface Cable Assy

D41955

Carrying Case

Replaceable Parts

B45009-1

N-Connector, Modified

B45009-2

N-Connector, Modified

B42893

EMI Shield

C41761

Liquid Crystal Display Assy

Part Number

Description

Qty

ND45417

Battery Pack Kit

ND45292

Main PCB Assy, S120A with RF
module and cables

ND45296

Main PCB Assy, S235A with RF
module and cables

ND45353

Main PCB Assy, S250A with RF
module and cables

ND48761

Main PCB Assy, S251A with RF
module and cables

D41766-3

Keypad PCB Assy

D40864-2

Membrane Keypad, Main

C41767

Membrane, Soft Keys

Hardware

790-171

Silicon Pad

761-10

Cap Vinyl, Black, round, 0.625
ID

790-52

Washer, #4, Shoulder, Nylon

900-257

Pan Head Screw, 0.312

790-445

Spacer PCB, 0.625, Self Mount

900-800

Pan Head Screw, #4, 0.312

900-811

Pan Head Screw, #4

900-326

Nut, Kep, 4-40, 0.312

900-697

Pan Head Screw, 4-40, 0.312

900-138

Screw, Pan, 2-56/patchlock,
0.18

B41753

Gasket, LCD

Case Parts

D40861-3

Case

C40863

Bumper

B45018

ID, Model S120A Label

B45017

ID, Model S235A Label

B46687

ID, Model S250A Label

48161

ID, Model S251A Label

Site Master MM

Содержание Site Master S251A

















Результаты поиска

Содержание Site Master S251A

Отзывы:

Похожие инструкции для Site Master S251A

Бренды по названию

Популярные бренды

Anritsu Site Master S251A, Руководство по обслуживанию

Результаты поиска

Содержание Site Master S251A

Отзывы:

Похожие инструкции для Site Master S251A

Бренды по названию

Популярные бренды