Anritsu Network Master Pro MT1040A, Руководство пользователя, Страница: 28 / 36

28
Additional Purchases
Adding New Options to Previously Purchased MT1040A
<MU100011A>
To add a new protocol option to a previously purchased MU100011A, choose the required option from the following list.
The MU100011A serial number is required to make the purchase.
Adding MU100011A Protocol Option Bit Rate Up to 10G Higher than 10G
Transport Technology
No. of
Measurement
Ports
* 1
1 (Single Channel) 2 (Dual Channel) 1 (Single Channel) 2 (Dual Channel)
Ethernet
IPv4/IPv6, Y.1564, IEEE 1588 v2, RFC 2544, BER, Multistream, OAM,
SyncE, MPLS, MPLS-TP, Multistage VLAN, PBB, Ping/Traceroute,
Cable Tests, In-band Control, Auto discovery
MU100011A-301
Up to 10G
Single Channel Retrofit
MU100011A-303
Up to 10G
Dual Channel Retrofit
MU100011A-317 *
8
Ethernet 25G
Single Channel Retrofit
—
MU100011A-313 *
9
Ethernet 40G
Single Channel Retrofit
—
MU100011A-315
* 9
Ethernet 100G
Single Channel Retrofit
—
TCP Throughput Test (RFC 6349, iPerf), Pass-through MU100011A-320
TCP Throughput
— —
SyncE Wander MU100011A-021*
10
SyncE Wander
—
Measurement using 100GBASE-SR — —
MU100011A-323 *
8
RS-FEC for 100GBASE-SR4
Retrofit
MU100011A-315
* 9
Ethernet 100G
Single Channel Retrofit
—
eCPRI/RoE (IEEE1914.3)
IPv4/IPv6, BER, VLAN, SyncE, IEEE 1588 v2, E-OAM
MU100011A-301
Up to 10G
Single Channel Retrofit
MU100011A-303
Up to 10G
Dual Channel Retrofit
MU100011A-317
* 8
Ethernet 25G
Single Channel Retrofit
MU100011A-375
* 7, * 8
eCPRI/RoE 25G Dual
Channel Retrofit
MU100011A-313
* 9
Ethernet 40G
Single Channel Retrofit
—
MU100011A-315 *
9
Ethernet 100G
Single Channel Retrofit
—
Measurement using 100GBASE-SR — —
MU100011A-323
* 8
RS-FEC for 100GBASE-SR4
Retrofit
MU100011A-315
* 9
Ethernet 100G
Single Channel Retrofit
—
OTN
* 2, * 3
Errors/Alarms, Error Performance/Delay/APS Test, FEC Test,
O.182 Test, Overhead Editing/Capture, TCM Monitoring/Generation,
Tributary Scan
MU100011A-301
Up to 10G
Single Channel Retrofit
MU100011A-303
Up to 10G
Dual Channel Retrofit
MU100011A-353
OTN 40G
Single Channel Retrofit
—
MU100011A-355
OTN 100G
Single Channel Retrofit
—
ODU Multiplexing Addition *
2,
*
4
MU100011A-363
ODU Multiplexing/Multi Stage Retrofit
ODU Flex Addition
* 2, * 5
MU100011A-362
ODU Flex Retrofit
—
CPRI/OBSAI
CPRI/OBSAI L1: Level/Bit Rate/Frequency deviation Measurement,
Alarms/Errors Detection, Unframed BER
CPRI/OBSAI L2: Link Status Monitoring, Alarms/Errors Detection,
Framed BER Measurement, RTD Measurement,
Monitoring using Passthrough
MU100011A-371
CPRI/OBSAI Up to 10G
Single Channel Retrofit
MU100011A-372
CPRI/OBSAI Up to 10G
Dual Channel Retrofit
MU100011A-373
CPRI 12/25G
Single Channel Retrofit
MU100011A-374
CPRI 12/25G
Dual Channel Retrofit
Fibre Channel
Performance Test, Signal Generation/Monitoring, Latency, BER,
Line Alarm/Error Monitoring
MU100011A-304
Up to 10G FC
Single Channel Retrofit
MU100011A-305
Up to 10G FC
Dual Channel Retrofit
MU100011A-391
FC 16G
Single Channel Retrofit
—
SDH/SONET
PDH/DSn Test, Tw-Way Monitoring/Mapping, Errors/Alarms,
Error Performance/Delay/APS Test, Header Monitoring/Generation,
Pointer Event Generation, Tributary Scan
MU100011A-301
Up to 10G
Single Channel Retrofit
MU100011A-303
Up to 10G
Dual Channel Retrofit
MU100011A-383
* 6
STM-256/OC-768
Client Signal Retrofit
—
*
1: The channel is not related to the physical port position. The user can freely choose either of the two physical ports assigned to the option via software.
For a dual channel setup, the two different ports can operate simultaneously with different bit rate of the same single protocol.
*
2: Please see the datasheet for supported OTN mapping.
*
3: When using the OTN function, the channel can be used as client signal mapped to OTN.
For example, when mapping STM-256/OC-768 to OTU4, both the MU100011A-355 (for physical port) and the MU100011A-383 (for client signal) are required.
*
4: When the ODU Multiplexing/Multistage option is installed, OTN multistage mapping measurements are supported.
This one option supports both single channel and dual channel.
*
5: This mapping function is based on the ODUFlex standard for transmissions over OTN networks and supports client signals of any speed.
*
6: The MU100011A has no STM-256/OC-768 PHY interface; it can be used for OTN client signals.
*
7: Option supports eCPRI/RoE protocol tests only.
*
8: FEC can be switched ON/OFF.
*
9: FEC is always OFF.
*
10: 40G and 100G are not supported.