anko VC8260-12A Скачать руководство пользователя страница 11

Страница: 11 / 12

TROUBLE SHOOTING

Problem

Possible causes

Solutions

The vacuum cleaner does not

switch on

1. The power button on unit

has not been depressed.

2. Bad contact to mains power

socket/ charger jack

1. Press again the power

button.

2. Check connection and see

if battery is fully charged

Suction not strong

1. Brush head not correctly

fitted.

2. The dust cup is full

3. The filters are blocked

1. Check brush head had

connected to main unit

2. Empty dust cup

3. Wash the filter

Floor head hard to push

Rolling brush may be jammed

with debris etc.

Ensure the vacuum cleaner is

switched off then remove the

debris from the rolling brush.

Or, the carpet may be too long

aSPECIFICATION

Model number

V8260-12A

Battery

14.8V 2000mAh, Li-ion (x4 cells)

Working time:

Fast setting : 20-30min

Slow setting : 30-40min

Charging time:

4-5hr

Battery charger

WJA-Y121750550W

Input:100-240V 50-60Hz 24W;

Output 17.5V d.c. 550mA

Содержание VC8260-12A













Результаты поиска

Содержание VC8260-12A

Отзывы:

Похожие инструкции для VC8260-12A

Бренды по названию

Популярные бренды

anko VC8260-12A, Руководство пользователя

Результаты поиска

Содержание VC8260-12A

Отзывы:

Похожие инструкции для VC8260-12A

Бренды по названию

Популярные бренды