Angelantoni CH1200 Скачать руководство пользователя

Страница: 49 / 49

13 REMOVAL FROM INSTALLATION SITE

The machine can be disassembled in order to move it from one site to another or in order to be scrapped.

Transport must be carried out in compliance with the norms described in this handbook in the chapter entitled
“HANDLING AND INSTALLATION”.

13.1 DISASSEMBLY

• In order to disconnect the machine from the mains supply, follow the procedure described for the electrical wiring in

reverse.

• Remove the supply cable coming out of the board and place it inside the board itself. In this way the machine can

be reassembled and can be started up again.

• Clean the surfaces accurately, oil the parts that could rust and cover the machine so as to protect it from dust, dirt

and humidity.

13.2 SCRAPPING

• In order to disconnect the machine from the mains supply, follow the procedure described for the electrical wiring in

reverse.

• Discharge all the refrigerant from the refrigerating circuit.

• Remove all the oil from the motors.

WARNING
• Do not waste refrigerating substances in the environment;
• Do not waste the compressor’s unfreezable oil in the environment;
• Do not waste polyiurethane in the environment.

It would be advisable to contact specialised companies for the disposal and the recycling of
the above materials.

• Divide the remaining parts according to their type and destroy in compliance with the laws in force.

• To remove and transport the machine please refer to the procedure described in the chapter entitled “HANDLING

AND INSTALLATION”.

Содержание CH1200


















































Результаты поиска

Содержание CH1200

Отзывы:

Похожие инструкции для CH1200

Бренды по названию

Популярные бренды

Angelantoni CH1200, Руководство по установке, использованию и техническому обслуживанию

Результаты поиска

Содержание CH1200

Отзывы:

Похожие инструкции для CH1200

Бренды по названию

Популярные бренды