Anest Iwata ZP2-H15, Инструкция по эксплуатации, Страница: 5 / 8

1
INSTRUCTION MANUAL
Spray Gun for Ceramic
Be sure to observe warning s and cautions in this instruction manual.
If not, it can cause paint ejection and serious bodily injury by drawing organic solvent.
Be sure to observe following marked items which are especially important
.
Indicates a potentially hazardous situation which, if not avoided, may result in serious injury or loss of
life.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury
or property damage.
Indicates notes which we ask you to observe. The safety precautions in this instruction manual are
the minimum necessary conditions. Follow national and local regulations regarding fire prevention,
electricity and safety as well as your own company regulations.
Symbol Marking on the Spray Gun:
II 2 G Ex h X
This ANEST IWATA spray gun
complies with 2014/34/EU Directive
relating to equipment and protective
systems intended for use in explosive
potentially atmospheres.
II 2 G Ex h IIB T6 Gb X
T
Amb
+5°C +40°C
Complies
with
European
Directive Specific
Marking for
Explosion
Protective Group II
(Surface)
Category
(Zone 1&2)
Type of
Atmosphere
(GAS)
Ignition
Protection
(not applied)
Explosion
Group
(Ethylene)
Temperature
Class
( 85°C)
Explosion
Protection
level
(EPL)
Additional
conditions:
Any static
Electricity
should be
discharged
and needs to
be diverted to
the ground via
a conductive
air hose not
included.
Ambient
Temperature
Important specifications
Max. Pressure 0.70MPa / 7.0bar / 100psi
Noise level 85dB(A)
Spray condition Recommended
Measuring point 1m backwards from spray gun, 1.6m height
Max. temperature Atmosphere: 5°C ~40°C (41°F~104°F) Air and Fluid: 5°C ~43°C (41°F~109°F)
Important
Never connect pressure feeding paint except pressure feed type spray gun.
*1. Atomizing air pressure means air pressure at spray gun inlet when trigger is pulled and air flows.
*2.Spray distance
：
250mm, Paint viscosity
：
20 seconds / NK-2
Nozzle needle assy combination
Fluid nozzle Fluid needle
Orifice mm (in) Mark Mark
1.5 (0.059)
/ ZP2 / 15
Non-mark
(Common parts)
2.0 (0.079)
/ ZP2 / 20
2.5 (0.098)
/ ZP2 / 25
Main specifications
Model Type of feed
Nozzle orifice
mm (in)
Air cap assy
Mark
Recommended condition
Air consumption
l/min (cfm)
*2
Pattern width
mm (in)
Air & fluid
connection
Mass
g (lbs.)
*1 Atomizing air
pressure
MPa (bar / PSI)
*2 Paint
output
ml/min
ZP2-H15
Pressure
1.5 (0.059)
ZP2-R1Z
0.34
(3.4 / 50)
560
500 (17.7)
330 (13.0)
Air
G1/4
(NPS1/4)
Fluid
G3/8
(NPS3/8)
385
(0.849)
ZP2-H20 2.0 (0.079) 670 350 (13.8)
ZP2-H25 2.5 (0.098) 760 370 (14.6)
This manual contains IMPORTANT
WARNINGS and INSTRUCTIONS.
Equipment in this manual is exclusively for
painting purposes.
Do not use for other purposes.
The operator shall be fully conversant with
the requirements stated in this instruction
manual including important warnings,
cautions and operation and correct handling.
Read and understand the instruction
manual, before use and retain for reference.