background image

 

 

Page 2 

Manual

 MF0145AXA.doc

         Manual for ION-M17P/19P Advanced

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

DISCLAIMER: 

This document has been developed by CommScope, and is intended for the use of its 
customers and customer support personnel. The information in this document is subject to 
change without notice. While every effort has been made to eliminate errors, CommScope 
disclaims liability for any difficulties arising from the interpretation of the information 
contained herein. The information contained herein does not claim to cover all details or 
variations in equipment, nor to provide for every possible incident to be met in connection 
with installation, operation, or maintenance. This document describes the performance of the 
product under the defined operational conditions and does not cover the performance under 
adverse or disturbed conditions. Should further information be desired, or should particular 
problems arise which are not covered sufficiently for the purchaser’s purposes, contact 
CommScope. 

CommScope reserves the right to change all hardware and software characteristics without 
notice. 

COPYRIGHT: 

© Copyright 2015 CommScope Inc. All Rights Reserved. 

This document is protected by copyright. No part of this document may be reproduced, 
stored in a retrieval system, or transmitted, in any form or by any means, electronic, 
mechanical photocopying, recording, or otherwise without the prior written permission of 
CommScope. 

TRADEMARKS 

All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of 
CommScope. Names of products mentioned herein are used for identification purposes only 
and may be trademarks and / or registered trademarks of their respective companies. 

 
Andrew Wireless Systems GmbH, 02-July-2015 
 

Содержание CommScope ION-M17P Advanced


















































Отзывы: