ANDELI
安德利
TIG-250GPLC
16
1
：请按照安装示意图正确的连接好焊枪，控制线及地线。所有接头务必连接紧固以防接
触不良造成焊机连接端子损坏。
1:
Please connect welding gun, control line and ground wire correctly in accordance with
installation diagram. All connectors must be connected and fastened so as to prevent
damage of terminal block of welding machine due to poor contact.
2
：请确保氩气管与焊机连接紧固密封，以防漏气，影响焊点质量
2:
Please be sure that argon tube and welding machine are connected, fastened and
sealed so as to prevent air leakage and influencing quality of welding spot.
3
：将焊机后面的接地螺丝用大于
4
平方的导线可靠接地，防止静电及漏电发生。
3:
Use wire which is greater than 4mm
2
to earth grounding screw behind the wielding
machine so as to prevent occurrence of static electricity and electric leakage.
氩弧焊操作方法：
Operation method of argon arc welding:
1
：打开氩气瓶的阀门并调好流量计至所需的流量。
1:
Turn on valve of argon gas bottle and adjust flowmeter to required flow.
2
：按下焊枪开关，电磁阀工作，枪头开始有氩气流出。
2:
Press welding gun switch, solenoid valve starts working and argon gas starts to
outflow from gun head.
3
：将钨极与工件距离
2
到
3
个毫米，按下焊枪开关开始引弧，根据工件厚度设置好适当
的焊接电流即可。
3:
Adjust distance between tungsten electrode and workpiece to 2~3 millimeters, press
welding gun switch to start striking the arc, set up proper welding current according to
thickness of workpiece.
连续脉冲点焊操作方法：
Operation method of continuous pulse spot welding:
1
：在连续脉冲点焊模式下需要设置三个参数：焊接电流，点焊时间，点焊频率用户可根
据工件的厚度设置适当的电流与点焊时间，点焊频率。然后按住枪开关不放以一定的速
度拖动焊枪移动即可焊出鱼鳞状的焊道，要结束焊接，松开枪开关即可。注意：在焊接
薄板时钨针和板的距离应控制在
0.5
毫米以下为佳。
1:
Three parameters need to be set up in the mode of continuous pulse spot welding:
welding current, spot welding time and spot welding frequency. User may set up
proper current, spot welding time and spot welding frequency in accordance with
thickness of workpiece. Then press and hold onto gun switch, drag welding gun to
move at a certain speed, weld scaly welding bead, and just loosen gun switch to stop
welding. Notes: when welding thin plate, the best distance between tungsten needle
and plate shall be controlled smaller than 0.5 millimeter.
2
：点焊频率与拖动焊枪移动的速度有着密切的关系，点焊频率低焊枪移动的速度应慢，
过快的速度会导致焊点与焊点之间连接不上影响焊接质量。点焊频率高焊枪移动的速度
应加快，频率越高焊道鱼鳞状越密。
2:
Spot welding frequency and speed of dragging welding gun are closely related, if spot
welding frequency is low, speed of moving welding gun shall be slow, fast speed will
lead to failure in connection between welding spots and influence welding quality. If
spot welding frequency is high, speed of moving welding gun shall be accelerated,
the higher the frequency, the denser of scaly welding beads.
3
：在连续脉冲点焊模式下，用户应根据工件的实际情况对焊接的参数进行多次调式，试
焊，以达到工艺要求为准。
3:
In the mode of continuous pulse spot welding, user should repeatedly debug and test
Содержание TIG-250GPLC
Страница 1: ...1...
Страница 13: ...ANDELI TIG 250GPLC 13 Welding current adjustment Single spot cold welding mode...
