background image

 

User manual 

Guangzhou Andea Electronics Technology Co., Ltd.                                                          12/15 
http://www.gzandea.com                   

Note: 

Step 1: In the software main interface, select the menu "Single Tag Test"; 

Step 2: In the "Single Tag Test" interface, select the type of tag to be operated; 

Step 3: mode: none address, address. 

        1) For a single tag, select the "none address" mode. 

             2) For multiple tags, select the "address" mode. 

Step 4: Click the "Inventory" button to display the UID list in UID drop-down box. 

Step 5: 1) For a single tag: click the "Connect" button; 

            2) For multiple tags: in UID drop-down box, select the tags required to be 

operated, and then click the "Connect" button; 

The green area represents 

the set operating area

 

Figure 15

 

Single tag reading and writing steps 

Steps: 

1) Set the data block of the tag to be operated in the Addr drop-down box and the 

Num  drop-down  box.  After  setting,  the  operable  data  block  is  displayed  in  green 

indicating that it can be operated; 

2) Click [Read Block] to read the data value of the data block selected in step 1; 

3) Write the value in the line (green area) of the data block whose value should be 

written, and then click [Write Block]; 

4) After the operation is completed, click the [Disconnect] button to disconnect the 

tag connection. 

Содержание RL865



















Отзывы: