AnaPico APPH6000 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 40

background image

APPH6000 User Manual V1.0 2010

- |

35

User Calibration (Firmware 1.0 and up)

User calibration is a function to correct the frequency response using correction data set for

phase noise, amplitude and baseband noise measurements.

This chapter describes the correction method and how to set up the calibration procedure.

Calibration and verification of the APPH6000 is performed by using the low frequency output

(FUNCT OUT) at the rear of the instrument. For calibration, the output is connected though a

short BNC cable to the BASEBAND IN input at the front panel.

User calibration procedure will be supported from firmware

and remote client revision 1.0

Please contact [email protected] to check availability.

«
...
33
34
35
36
37
...
»

Содержание APPH6000









































Отзывы:

Нет отзывов

Похожие инструкции для APPH6000

Бренд: KTMAII Страницы: 11

FUSIONESCO MULTI CHOP

Бренд: JAP Страницы: 56

Anthony Worrall Thompson VFP014

Бренд: Breville Страницы: 28

Бренд: Coline Страницы: 12

Бренд: Estia Страницы: 17

Бренд: Primada Страницы: 32

Бренд: Prima Страницы: 7

Universal Signal Processor USP 405

Бренд: Extron electronics Страницы: 3

Бренд: camry Страницы: 36

Бренд: Danby Страницы: 22

Бренд: MIA Страницы: 14

Бренд: Daewoo Страницы: 14

Бренд: Kambrook Страницы: 28

Symphony DSP56724

Бренд: Freescale Semiconductor Страницы: 436

Бренд: Bosch Страницы: 80

Бренд: Bosch Страницы: 134

Бренд: Bosch Страницы: 135

Бренд: Bosch Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды