AnaPico APPH6000 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 40

background image

APPH6000 User Manual V1.0 2010

- | Remote Programming the APPH6000

32

A range of standard software such as NI-VISA or Agilent IO Config is available to setup the

computer/signal generator interface for the VXI- 11 protocol. Please refer to the applicable

software user manual and documentation for information on running the program and

configuring the VXI-11 interface. The program is used to configure the LAN client. Once the

computer is configured for a LAN client, you can use the VXI- 11 protocol and the VISA library to

send SCPI commands to the signal generator over the LAN interface. Example programs are

available on request under

[email protected]

.

VISA is an IO library used to develop IO applications and instrument drivers that comply with

industry standards. It is recommended that the VISA library be used for programming the signal

source analyzer. The NI-VISA and Agilent VISA libraries are similar implementations of VISA and

have the same commands, syntax, and functions.

Using the USB-TMC Interface with VISA (Firmware 1.0 and

up)

The USB (Universal Serial Bus) remote control system provides device control via USB, which is

equivalent to control via LAN or GPIB. Connection is made through an interface in compliance

with USBTMC-USB488 and USB 2.0

Type B: USB (USBTMC) interface port

The APPH6000 conform to USB Test & Measurement Class (USBTMC) protocol. This simplifies

instrument control considerably because such devices behave just like GPIB devices when

communicating.

The USB can identify devices automatically, so once you connect a USB cable to a target device,

a dialog box will appear for USB device registration. You must install the VISA Libraries on your

PC in advance. The USB can identify devices automatically, so once you connect a USB cable to a

target device, a dialog box will appear for USB device registration.

Please see the APPH6000 Programmer’s Manual for further details.

«
...
30
31
32
33
34
...
»

Содержание APPH6000









































Отзывы:

Нет отзывов

Похожие инструкции для APPH6000

Бренд: Love Controls Страницы: 8

Бренд: EVS Страницы: 48

Бренд: ECG Страницы: 56

Бренд: Black & Decker Страницы: 4

Бренд: Hamilton Beach Страницы: 40

Бренд: Audiotec Fischer Страницы: 20

Бренд: Zelmer Страницы: 72

Ma Cuisine C 3200

Бренд: MAGIMIX Страницы: 130

Бренд: XTA Страницы: 58

Бренд: Unika Страницы: 40

Бренд: Black & Decker Страницы: 3

Бренд: Black & Decker Страницы: 25

Бренд: Black & Decker Страницы: 24

Бренд: Black & Decker Страницы: 56

Бренд: IDEALE Страницы: 18

Бренд: Deni Страницы: 1

Бренд: izzy Страницы: 23

Бренд: Texas Instruments Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды