Analog Devices EVAL-SSM3582Z Скачать руководство пользователя страница 4

Страница: 4 / 14

UG-934

EVAL-SSM3582Z User Guide

Rev. 0 | Page 4 of 13

EDGE MODE

To reduce the radiated emissions from the

SSM3582

amplifier,

an edge rate control mode is available. Register 0x05, Bit 3,
controls the edge rate of the switching. This low electromagnetic
interference (EMI) mode is enabled by default. To disable the
low EMI mode, set Bit 3 of Register 0x05 to 0. To return to the
low EMI mode, set Bit 3 of Register 0x05 to 1.

MONO OPERATION

The board is configured for stereo operation by default, but can
be changed to mono operation.
For mono operation, the R27 through R30 resistors must be
fitted with 0 Ω or use 16 AWG wires to short the OUTL+ terminal
to the OUTR+ pin, and, similarly, to short the OUTL− terminal
to the OUTR− pin. Note that the device must be configured to
mono operation by setting the MONO bit (Bit 4, Register 0x04) to
0 before turning on the power stage.

Set this bit by writing Register 0x04 with the hexadecimal value,
0xB1. This ensures the power stage turns on in mono operation.

COMPONENT SELECTION

Selecting the proper capacitors and ferrites for the evaluation
board is key to achieving the performance required at the cost
budgeted.

Output Shunting Capacitors

There are four output filter capacitors, C1, C2, C39, and C40, that
work with the L2, L3, L6, and L7 ferrite beads. Use small size
(0603 or 0402), multilayer, ceramic capacitors of dielectric type
X7R or COG (NPO) materials. The recommended value of the
capacitors is 220 pF.

Output Ferrites

If ferrite beads are preferred for EMI filtering at the output
nodes, Table 1 shows the recommended components to avoid
excessive noise induced by the nonlinear behavior of ferrite
beads.

Table 1. Recommended Output Ferrite Beads

Part No.

Manufacturer

Z (Ω at 100 MHz)

MAX

(mA)

DC Resistance (DCR) (Ω)

Size (mm)

NFZ2MSM101SN10

Murata Manufacturing Co.

100

4000

0.014

2.0 × 1.6 × 0.9

NFZ2MSM181SN10

Murata Manufacturing Co.

180

3400

0.020

2.0 × 1.6 × 0.9

NFZ2MSM301SN10

Murata Manufacturing Co.

300

3100

0.024

2.0 × 1.6 × 0.9

Contact Murata Manufacturing Co. for further options.

OPTICAL IN

COAXIAL IN

OPTICAL/COAX

SELECTOR SWITCH

C CONNECTOR

FOR USBi

LEFT OUTPUT

RIGHT OUTPUT

RESET SPDIF RX

SERIAL INPUT

SELECT

SPDIF/EXT

DEVICE ADDRESS

SETTING JUMPERS

1.8V REGULATOR
INT/EXT SELECT

1.8V LDO

ENABLE/DISABLE

3.3V REGULATOR
INT/EXT SELECT

3.3V REG
ENABLE/DISABLE

5V INT/EXT SELECT

5V REG ENABLE/DISABLE

PVDD IN

C/STANDALONE

SELECT SWITCH

C PULLUP

SELECTOR

5V LDO ENABLE

14262-

003

Figure 3. Board Settings

Содержание EVAL-SSM3582Z















Результаты поиска

Содержание EVAL-SSM3582Z

Отзывы:

Похожие инструкции для EVAL-SSM3582Z

Бренды по названию

Популярные бренды

Analog Devices EVAL-SSM3582Z, Руководство пользователя

Результаты поиска

Содержание EVAL-SSM3582Z

Отзывы:

Похожие инструкции для EVAL-SSM3582Z

Бренды по названию

Популярные бренды