background image

User Guide

UG-1533

ORDERING INFORMATION

ESD Caution
ESD (electrostatic discharge) sensitive device

. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary

protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of
functionality.

Legal Terms and Conditions

By  using  the  evaluation  board  discussed  herein  (together  with  any  tools,  components  documentation  or  support  materials,  the  “Evaluation  Board”),  you  are  agreeing  to  be  bound  by  the  terms
and  conditions  set  forth  below  (“Agreement”)  unless  you  have  purchased  the  Evaluation  Board,  in  which  case  the  Analog  Devices  Standard  Terms  and  Conditions  of  Sale  shall  govern.  Do  not
use  the  Evaluation  Board  until  you  have  read  and  agreed  to  the  Agreement.  Your  use  of  the  Evaluation  Board  shall  signify  your  acceptance  of  the  Agreement.  This  Agreement  is  made  by
and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of
the  Agreement,  ADI  hereby  grants  to  Customer  a  free,  limited,  personal,  temporary,  non-exclusive,  non-sublicensable,  non-transferable  license  to  use  the  Evaluation  Board  FOR  EVALUATION
PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for
any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or
distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees,
affiliates  and  in-house  consultants.  The  Evaluation  Board  is  NOT  sold  to  Customer;  all  rights  not  expressly  granted  herein,  including  ownership  of  the  Evaluation  Board,  are  reserved  by  ADI.
CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the
Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board
to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any
modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to
the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to
Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI
MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR
WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS
FOR  A  PARTICULAR  PURPOSE  OR  NONINFRINGEMENT  OF  INTELLECTUAL  PROPERTY  RIGHTS.  IN  NO  EVENT  WILL  ADI  AND  ITS  LICENSORS  BE  LIABLE  FOR  ANY  INCIDENTAL,
SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST
PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US
DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal
laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts
(excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly
disclaimed.

Trademarks and registered trademarks are the property of their
respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Rev. A | 30 of 30

Table 5. EVAL-PMD-IB1Z Bill of Materials
Qty

Reference Designator

Description

Manufacturing

Part No.

3

+12 V, 3P3V, 3V3AUX

Connector PCB test points, red

Keystone Electronics

5000

1

C1

0.1 µF ceramic capacitor, X7R

AVX

06035C104KAT2A

1

DS1

LED, green, clear

Fairchild

QTLP600C4TR

1

J1

Connector, PCB, straight, Subminiature Version A (SMA)

TE Connectivity Ltd

5-1814832-1

3

P1 to P3

Connector headers, female, 12 position, right angle, gold, 2.54 mm pitch

Sullins

PPPC062LJBN-RC

1

P2

FMA connector, single-ended array, male, 160 position

Samtec

ASP-134604-01

25

R1 to R25, R59

0 Ω film resistors, SMD, 0603

Panasonic

ERJ-2RKF2003X

1

R26

2.4 kΩ resistor, precision thick film chip

Panasonic

ERJ-2RKF2R4X

1

U1

2 Kb serial I

2

C bus electronically erasable programmable read-only

memory (EEPROM)

ST Microelectronics

M24C02-WMN6TP

I

2

C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).

Содержание EVAL-ADAQ4001FMCZ































Отзывы: