![background image](http://html.mh-extra.com/html/amx/axlink-bus-controllers-axb-232/axlink-bus-controllers-axb-232_instruction-manual_2937451006.webp)
Product Information
2
AXB-232++ RS-232/422/485 Interface
Specifications
The following table lists the specifications for the AXB-232++.
Specifications
Power
12 VDC @ 160 mA
Processor
On board 32-bit processor and 384K (of non-volatile memory) run Axcess
programs independent of the control system. This relieves the AXlink bus and
controller for the processing time for controlling those devices. (Requires Axcess
Version 3.0 or higher.)
Asynchronous data
standards
• Baud rates -
300
,
600
,
1200
.
2400
,
4800
,
9600
,
19200
and
38400
.
56400
is supported via the BAUDMED Send Command (see the
Send_Commands
section on page 9 for details).
115200
is supported via the BAUDHIGH Send Command (see the
Send_Commands
section on page 9 for details).
• Data bits - 7, 8, and 9
• Stop bits - 1 and 2
• Parity -
None
,
Odd
,
Even
,
Mark
and
Space
Buffers
• 1KB input buffer
• 1KB AXlink buffer
Front Panel
AXlink LEDs
Green AXlink status indicator:
•
Full-Off
indicates no power is being received or the controller is not functioning
properly.
•
One blink per second
power is active and AXlink communication is functioning.
•
Full-On
indicates power is active and AXlink data communication is not
functional.
RX LED (Red)
Blinks to indicate the AXB-232++ is receiving RS-232, RS-422, or RS-485 data.
The RX LED blinks even if the data being received is incorrect.
TX LED (Red)
Blinks to indicate the AXB-232++ is sending RS-232, RS-422, or RS-485 data.
DEVICE DIP Switch
An eight-position DIP switch used to set the device number for the AXB-232++.
Refer to
Setting the DEVICE DIP switch, on
page 4, and
Setting jumper JP5 to set
the RS-422 port for RS-485 use
section on page 4 for more information.
RS232/422 DIP Switch
An eight-position DIP switch used to set the communication parameters for the
RS-232/422 device. Refer to
Setting the RS-232/422 DIP switch
, on page 5, for
more information.
Rear Panel
Hardware handshaking
connector
An RTS/CTS data connector that can be wired for hardware handshaking if called
for by the controlled device (4-pin male).
RS422/232 connector
A captive-wire connector wired for RS-422/232 data control (8-pin male).
AXlink connector
Receives power and data via the AXlink bus and AXlink system controller
(4-pin male).
Internal Jumpers
Sets differential input termination and enables RS-485 output.
Supports
XON/XOFF software and hardware handshaking
Dimensions (HWD)
1.5" x 5.5" x 5.5" (3.81 cm x 13.97 cm x 13.97 cm)
Weight
1.1 lbs. (498.95 g)
Enclosure
Metal with black matte finish
Included Accessories
• AXlink connector (4-pin female)
• Phoenix connector (8-pin male)
Optional Accessories
• CC-232 Control Cable
• AC-RK Accessory Rack Kit
• 12 VDC power supply, 800 mA
Содержание AXlink Bus Controllers AXB-232++
Страница 1: ...instruction manual AXlink Bus Controllers AXB 232 RS 232 422 485 Interface ...
Страница 2: ......
Страница 4: ...ii AXB 232 RS 232 422 485 Interface Table of Contents ...