background image

Sizing Chart

Amtrol

Pressuriser

®

Minimum 

Flow Rate

From City 

Supply

Minimum 

Flow Pressure 

From City 

Supply

Minimum

Incoming 

Pipe Size

Water

Meter

RP-10HP 10 gpm

10 psig

3

/

4

"

3

/

4

"

RP-15HP 15 gpm

10 psig

1"

1"

RP-25HP 25 gpm

10 psig

1

/

4

"

1

/

4

"

Metal piping must be used for all inlet and outlet lines to the unit. 

Do not oversize pump. Inadequate water supply will result in 

poor performance and pump damages.

Pre-Installation

•  DO NOT USE FOR PRE-HEATED WATER SUPPLIES;
• DO NOT USE FOR ANYTHING EXCEPT COLD WATER 

(AMBIENT TEMPERATURE NOT TO EXCEED 100° F);

• DO NOT USE IN SYSTEMS WHERE LOW PRESSURE IS 

DUE TO LEAKS OR WHERE LEAKS IN THE PLUMBING 

SYSTEM MAY EXIST;

•  DO NOT USE IN SYSTEMS WHERE THE WATER SUPPLY 

CAN DROP BELOW 10 PSIG;

• DO NOT USE IN SERIES WITH ANOTHER PUMP (SUCH 

AS IN PRIVATE WELL WATER SYSTEMS); 

• DO NOT RE-PRESSURIZED TANK AFTER INITIAL 

INSTALLATION; 

• DO NOT PIPE EXCEPT WITH METAL PIPING AT INLET 

AND OUTLETS. 

The system must be placed indoors only

 on a solid level 

surface with a drip pan piped to a drain with adequate capacity 

for large volumes of water in the event the system ruptures or 

fails. Consider the risks posed by tanks under pressure and the 

potential for leaking and/or flooding damage in selecting the 

location. The unit must not be placed in an environment that would 

expose the water in the tank to temperatures below freezing or in 

excess of 100° F.

Be sure to leave a minimal 

clearance of 12” around 

the unit for access should 

field adjustments be 

necessary in the future 

and to permit maintenance 

and inspection (Figure 1).

Installation

1. 

Remove protective air valve cap.

2.  

Check pre-charge pressure (pressure should be + or – 10% of 

the factory setting). Factory pre-charge is 38 psig.

3. 

Release or add air as necessary to make the pre-charge 

pressure 2 psig below the pressure switch pump cut-in setting.

4.  

Replace protective air valve cap. (Remove air valve label, 

replace protective air valve cap, peel off backing of label and 

apply on air valve cap.)

MINIMUM SUPPLY LINE AND METER SIZE FOR 

THE RP-10HP IS 

3

/

4

", THE RP-15HP IS 1" AND 

THE RP-25HP IS 1

1

/

4

". THIS APPLIES TO ALL LINES INCLUDING 

THOSE USED WITH THE WATER METER OR FITTINGS BEFORE THE 

PUMP. CONTACT FACTORY IF MINIMUM FITTING/LINE SIZE IS 

BELOW THE ABOVE NUMBERS.

5. 

Install a 

SPRING LOADED CHECK VALVE 

in the city supply 

line on the suction side of the pump along with a shut-off valve. 

Failure to do so will result in premature failure of the AMTROL 

Pressuriser due to excessive pump cycling.

6.  

Install a by-pass loop (Figure 2).

7.  

Pipe the city supply after the shut-off valve to the suction side 

of the pump, as shown.

8. 

Connect the house supply line using a 100 psig maximum relief 

valve as shown (Figure 2). It is important that the pressure 

relief valve be installed on the pump discharge 

prior

 to any 

shut off valves.

PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY

IMPORTANT GENERAL SAFETY INFORMATION - 

ADDITIONAL SPECIFIC SAFETY ALERTS APPEAR IN THE FOLLOWING INSTRUCTIONS.

If the control is set too high or the pump is running 

when the water supply is shut off and there is no 

demand on the system, the pump will run continuously, can overheat 

and become damaged, potentially  resulting in product failure, leaking 

and/or rupture. 

All wire and fuse sizings are preliminary 

recommendations only.  For your safety, local 

codes, and in their absence, national codes must be followed to minimize 

the risk of electric shock, property damage or personal injury.

The pump motor is designed for use with single 

phase, 60Hz ac.  Use with any other type of power 

will cause damage to the motor.  The pump models RP-10HP, RP-15HP 

and RP25-HP are pre-wired for 115 vac; however, they can be rewired to 

be used with 230 vac.  Consult motor nameplate for the wiring diagram.

The power for your pump must be on a dedicated 

circuit.  In addition, a shut off switch should be 

visible and near the pump.  Use a 20 amp circuit.

Before attempting any service and disassembly, 

shut off power to the pump.  Ensure power is 

disconnected prior to removing motor.  Ensure power is disconnected 

before cleaning is attempted.

Grounding of the pump is essential for your 

protection and the protection of the motor.  All wiring 

should be completed by a licensed electrician, and in accordance with 

local codes or in their absence, the National Electrical Code.  Before 

starting the wiring installation, disconnect all power to the circuit to be 

used for the AMTROL Pressuriser

®

.

The AMTROL Pressuriser

®

 should only be 

connected to a municipal, cold water supply, and in 

systems with a minimum pressure of 10 psig at all times, measured under 

flow at the tap closest to the location of the AMTROL Pressuriser

®

 

installation. 

12"

Amtrol Pressuriser

®

 

Figure 1

SPRING

CHECK VALVE

FLOW

FLOW

BYPASS
LOOP

PRESSURE

RELIEF

VALVE

CITY

WATER

SUPPLY

TO SYSTEM

SHUT-OFF

VALVES

RP-10HP

RP-15HP

RP-25HP

Figure 2

Отзывы: