background image

Mounting Angle Diagram B

(Recommendations are the same right to left and front to back)

Mounting angle above horizontal is not recommended

1

5

16

(1.3125)

(.25)

2

1

4

1

4

(2.25)

7. Use plastic ties (BP-46) to secure hose in position and away from potential damage. Trim ties with

side cutter. 

Note:

Over tightening the plastic ties may cause the hose to collapse and restrict oil flow.

8. Fill the selected Full-flow and By-pass filters with the same motor oil being used in the vehicle. Lubricate

the filter gaskets with oil and spin filters onto mount. Tighten per instructions on the filter can.

E. Start up procedures

1. Check that all fittings and hoses are securely attached, and that the hoses are routed properly.
2. Check engine oil level. Fill to full mark if necessary.
3. With the equipment secured start the engine and immediately check oil pressure. 

Note:

Pressure

may initially take a moment or two to rise. Installing the Dual Remote By-Pass System may
result in a slight vibration sound in some applications. No harm to the engine will occur. Please
contact AMSOIL Technical Services for more information.

Caution: 

Carefully check for leaks at fittings, hoses and mount. If leaks are observed, 

STOP

ENGINE IMMEDIATELY,

repair leaks and continue.

4. After engine has warmed, shut off and re-check engine oil level. Top off as necessary.
5. Record equipment/operating hours and date of installation.

F. Periodic maintenance

1. Periodic visual inspection of the fittings and hoses is recommended. Check for leaks, hose

deterioration and cuts. Repair and/or replace as necessary.

2. Refer to Recommended Filter Change Interval chart for servicing intervals.
3. To change the filter elements:

a. Ensure engine is off and use caution as the engine, oil and filter may be hot and could result

in an injury.

b. Using a filter wrench, remove the filter elements. Dispose of properly.
c. Clean the filter gasket contact areas on the mount with a clean, lint-free rag.
d. Lubricate the new filter gaskets with clean oil or grease.
e. Fill filters as full as possible with engine oil.
f. Screw on new filters, tighten per instructions on the filter can.
g. Start engine and check for leaks.
h. Check engine oil level, fill as needed.

4. Record equipment/operating hours for future reference.

GOOD

ANGLE

ACCEPTABLE

ACCEPTABLE

GOOD

ANGLE

PREFERRED MOUNTING ANGLE

HORIZONTAL

20°

50°

130°

160°

180°

Parts and assembly list

Dual Mount By-pass Filter System (BMK-27) for GM Duramax

Item

Description

Qty.

Part No.

1.

Filter Mount Assembly

1

BK-309

2.

Allen Head Plug

2

BP-191

3.

1

4

20 x 1

Hex Head Bolt

4

BP-23

4.

1

4

I.D. Washer

6

BP-21

5.

1

4

Self Locking Nuts

8

BP-22

6.

90 degree fitting 

7

8

-14 x  

5

8

JIC

1

BP-331

7.

“O” ring fitting 

7

8

-14 x  

5

8

JIC

3

BP-289

8.

Hose Fitting

4

BP-360

9.

1

2

 

I.D. hose

12

BP-350

10.

Spin-On Adapter

1

BP-420

11.

Adapter Retaining Nut 

13

16

-16

1

BP-405

12.

Gasket 3.11

ID

1

BP-220

13.

Mounting Bracket Top

1

BP-194

14.

Mounting Bracket Bottom

1

BP-195

15.

1

4

-20 x 1

1

2

Hex Head Bolt

4

BP-185

16.

1

4

ID Fender Washer

4

BP-186

17.

Adapter Nut O-ring

1

BP-346

Full-Flow Filter

1

EaO-26

By-Pass Filter

1

EaBP-100

Plastic Tie

2

BP-46

Thread Sealant

1

BP-198

Instruction Sheet

1

BP-258

Optional Parts

Oil Sampling Kit

1

BK-13

Deluxe oil sampling valve 

1

4

NPT

1

G1570

(Must also order fitting BP209)
90 degree fitting 

7

8

-14 x 

5

8

JIC

1

BK-21

45 degree fitting 

7

8

-14 x 

5

8

JIC

1

BK-22

Mounting Template

Diagram C

Minimum Bend Radius

2

1

4

(1.5) 

1

2

I.D. Hose BP-350

By-Pass

Filter

Full-Flow

Filter

Diagram A

MINIMUM AREA NEEDED FOR 
DUAL MOUNT AND SPIN-ON OIL FILTER ELEMENTS
* Mount and element heights plus 1-inch removal clearance

BP258_95064  9/24/09  11:03 AM  Page 2

Содержание BMK-27







Отзывы: