AMS 28 Slim Gem Скачать руководство пользователя страница 36

Страница: 36 / 51

L0126J

CLEARING JAMMED MOTOR

If one or more motors and helices become jammed, the motor(s)
will be displayed as a sublevel error under “Motor Jammed”.

Energized vend motors can turn a helix with considerable
torque, creating a possible entrapment hazard. Disconnect
power to the vendor or control board before freeing a
jammed helix or motor. Always restrain or block the helix
before freeing a jammed or caught product.

CAUTION

Use caution when freeing jammed product (Refer

to SAFETY PRECAUTIONS on page 7)!

Clear any jammed products from the indicated vend columns.

To reset the error, first enter service mode, then select Tray Setup
(Refer to

TRAY SETUP

on page 22). Press “

”, then “

“, then

“

”. The control will attempt to run the jammed motors. If the

motor had been taken out of the motor matrix, it will be re-
established in the matrix.

MACHINE TROUBLESHOOTING CHART

The following troubleshooting chart may be used to find quick
remedies for electrical and mechanical failures in the vendor.

MACHINE TROUBLESHOOTING CHART

IF A REPLACEMENT PART IS NECESSARY, PLEASE CONTACT YOUR DISTRIBUTOR

Symptom

Possible Cause

Remedy

No power at the control board. (no
beeping sound during power-up or

when the service mode button is

pushed).

No power from power cord.

Check power cord, outlet or supply.

3.0 amp fuse is blown.

Replace 3.0 amp fuse.

Fuse harness is not connected to the back of the

fuse holder.

Connect fuse holder harness.

Short or cut in the power harness

between the transformer and control board.

Check continuity through the power

harness. If there is no continuity

replace the power harness.

Transformer does not have power at the 24 VAC

secondary side.

Insure primary side of transformer is

receiving power. If there is not at

least 29 VAC on secondary side

replace transformer.

Vendor displays “Please Make

Another Selection”.

Selection not configured in the motor matrix.

Reconfigure the motors. Check for

motor coupling.

Motor jammed.

Clear jammed motor and clear error

code.

Vend not sensed by sensor.

Clear fault in sensor boards or

harness: possible control board error.

Vendor does not accept coins.

Options set for “Free Vend”.

Scroll to Free Vend and change to

Changer unplugged.

Plug in changer.

Coins jammed.

Clear changer.

Defective changer or other MDB device.

Replace changer.

Credit amount exceeds the highest price. (Prices

may be set at $0.00.)

Set prices.

Control board is in service mode.

Exit service mode.

Vendor will pay out coins.

Changer unplugged.

Plug in changer.

Defective changer.

Replace changer.

Coins jammed.

Clear jammed coins.

No coins in changer.

Add coins to the changer.

7 TROUBLESHOOTING

Содержание 28 Slim Gem




















































Результаты поиска

Содержание 28 Slim Gem

Отзывы:

Похожие инструкции для 28 Slim Gem

Бренды по названию

Популярные бренды

AMS 28 Slim Gem, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 28 Slim Gem

Отзывы:

Похожие инструкции для 28 Slim Gem

Бренды по названию

Популярные бренды