AMQ ACTIV-Pro3 Скачать руководство пользователя страница 5

ACTIV-PRO3  

ASSEMBLY GUIDE  |  5

amqsolutions.com

    

SAFETY INSTRUCTIONS

When using an electrical furnishing, basic precautions should always be followed, including the following: 
Read all instructions before using (this furnishing) . PLEASE SAVE THESE INSTRUCTIONS, AND THE USER 
GUIDE, IN AN OBVIOUS PLACE FOR THE END USER AFTER ASSEMBLY . 

To reduce the risk of burns, fire, electric shock or injury to persons:

1 .  Always unplug this furnishing from the electrical outlet before cleaning .
2 .  Use this table only for its intended use as described in these instructions . Do not use attachments not 

recommended by the manufacturer .

3 .  Never operate this table if it has a damaged cord or plug, if it is not working properly, or if it has been 

dropped or damaged .

4 .  Keep the cord away from heated surfaces .
5 .  Never drop or insert any object into any opening .
6 .  Do not use outdoors .
7 .  Do not operate where aerosol (spray) products are being used or where 

oxygen is being administered .

8 .  For loading always put heavier items at the bottom and not near the top in 

order to help prevent the possibility of the furnishing tipping over .

9 .  Do not sit/stand on product .
10 .  Inspect regularly, stop using if damaged or loose parts found .

The desk or table shall be installed near power socket & the plug shall be 
easily accessible.

WARNING - Risk of fire and shock

POLARIZED PLUG INSTRUCTIONS (Only for products with polarized plug)

 

To reduce the risk of electrical shock, some furnishings have a polarized plug (one 
blade is wider than the other) like the plug illustrated in Figure 1 . This plug will fit in 
a polarized outlet only one way . If the plug does not fit fully in the outlet, reverse the 
plug . If it still does not fit, contact a qualified electrician to install the proper outlet . 
Do not change the plug in any way .

INSTRUCTIONS FOR DOUBLE INSULATED PRODUCTS:

 No grounding 

means is provided on a double-insulated product . Nor is a means for grounding 
to be added to the product . The plug looks like the plug illustrated in Figure 1 . A 
double insulated product is marked with the words “double insulation”, “double 
insulated .”

GROUNDING INSTRUCTIONS (for grounded products only)

 - Some 

products must be grounded . Connect these types of appliances to a properly 
grounded outlet in accordance with all local codes and ordinances .

For products sold in North America and other 120V regions: the product is for use 
on a nominal 120-V circuit . These products use a grounded plug that looks like the 
plug illustrated in sketch A in Figure 2 . Make sure that the product is connected to an outlet having the same 
configuration as the plug . No adapter should be used with this product . WARNING - Risk of fire and shock, 
Use only type SJT 18 AWG cord . 

PLUG ILLUSTRATION DISCLAIMER - Illustrations shown here may not match your product.  
Depending on your region, the plug pin size and shape may change.

OPERATING INSTRUCTIONS

Please refer to the User Guide, which is available online .

WARNING

GROUNDED

OUTLET

GROUNDED

OUTLET BOX

GROUNDING PIN 

Figure 1

Polarized Plug

Figure 2

Grounding methods

Products with Grounded Plugs

Products with Polarized Plugs

Содержание ACTIV-Pro3


























Отзывы: