8
sw915 digital audio travel partner
WireleSS microphone Setup and operation
We use only the best wireless microphones for our PA systems. Audio-
Technica’s 700 Series Freeway wireless delivers professional features
and sound quality unheard of in its class. These easy-to-use wireless
systems feature eight selectable frequency-coordinated channels,
diversity operation for increased range/reliability, automatic frequency
scanning, Tone Lock™ squelch and more. For multiple-mic applications,
as many as eight systems may be used together.
TrANSmiTTEr SETup, CONTrOLS ANd FuNCTiONS
BatterY seleCtion:
Two 1.5V AA type alkaline batteries
Belt paCK transmitter Battery installation:
1. Open the transmitter door by first pulling the catch down and then
sliding the door upward.
2. Observe correct polarity as marked and carefully insert two fresh
1.5V AA alkaline batteries.
3. Slide the door closed making certain it clicks securely in place.
HandHeld wireless Microphone Battery installation:
power /Mute Battery indicator:
After the battery is installed, press and hold the power button unit until
the battery indicator LED turns green (it will first turn red, keep holding
until it turns green). If the battery indicator LED does not light up when
the power button is pressed, the batteries are installed incorrectly or
they are dead. The LED will flash to indicate low-battery condition. Press
and hold power button to shut unit off (light shuts off).
Mute Function:
With the transmitter on, a slight touch of the Power/Mute button will
toggle between muted and live operation. Red led indicates muted
operation, Green LED indicated live operation.
reCeiver Controls and FunCtions
tHe power switCH on tHe HandHeld MiCropHone is Built
into tHe power/Mute/BatterY Button, wHiCH is loCated on
tHe Base oF tHe MiCropHone.
1. Unscrew the lower body cover slide it downward, and remove it to
expose the battery compartment.
2. Observe correct polarity as marked inside the battery compartment
and carefully insert two fresh 1.5V AA alkaline batteries. Insert the
first battery and slide it toward the spring contact. Then insert the
second battery into the space remaining. Make certain the batteries
are fully seated in the battery compartment.
3. Slide the lower body compartment back on and screw the housing
together. Do not over tighten.
Note: Remove batteries from the handheld transmitter starting at the
bottom end, where finger indents in the battery housing are provided
for easy grip.
1
2
3
4
5
antennas
: Are positioned internally at the optimal 45 degree angle for
best reception.
1 - aF peaK indiCator:
Indicates when maximum transmitter
modulation without distortion has been reached. Not affected by
position of Volume control (Fig. C).
2 - led window:
LED Display indicates channel setting and scanning
operation.
3 - diversitY indiCators:
Indicates which antenna (A or B) has better
reception and is in operation.
4 - seleCt Button
(for manual channel selection): Press the Select
button repeatedly until desired channel is reached. Press and hold the
Set/Scan button to manually set the receiver to indicated channel.
Channel number will stop flashing. (A brief touch of the Set/Scan button
will revert to previously set channel). If the Set button is not pressed
within 10 seconds to confirm the selection, the system will revert to its
original channel.
5 - set/sCan Button:
The Set/Scan button can be used in two ways:
1) in conjunction with the Select button to permit manual selection
of an operating channel in Manual Set Mode (see “Select button”
description above); and 2) Automatic Scan/Set Mode, to initiate the
automatic channel scan and selection, as follows: Automatic Scan/Set
Mode: Press and hold the Set/Scan button for about two seconds. The
current channel will flash three times quickly; then the system will begin
to scan for the next open channel. When it finds an open channel, it
will flash the open channel three times and then set the channel. (If an
open channel is not found, the automatic scan will return to the original
channel and flash 5 times.)
CAuTiON!
The small trimmer controls are delicate; use only the
supplied screwdriver. Do not force the trimmers beyond their normal
180 degree range of motion.
Return the screwdriver to its storage clip when not in use.