(3),
以布线状态拉动线束靠近合金外壳,
转动R4 holder, 使其止转切面与合金外壳的2/3pos中心连线相
垂直;
并保持R4 holder与线缆相对位置;
drag the cable end close to alloy shell in service
state,
rotate R4 holder, have its anti-rotation chamfer surface vertical to link line of the 2/3pos
center in alloy shell;
hold relative position of R4 holder & cable;
(4),
拉直线缆
,
记录此时R4 holder 止转切面与步骤
9
已组装完成端插头的相对角度, 并记录;
stretch
the cable, record angle between R4 holder anti-rotation chamfer surface and plug end assembled
done in step
9
;
(5),
拔下合金外壳;
remove the alloy shell from receptacle;
3 of 3
™
Rev. 2
®
11
,
组装线束
另一端
.
assemble plug on
the other end
of cable.
10,
将步骤
9
组装好的插头插接到 对应的PDU/负
载插座上.
plug the connector end done in
step
9
to corresponding PDU or load
receptacle panel.
(1), 再
取一套零件, 按步骤1～4操作, 套上端子,
暂不压接端子
;
take another set plug components,
assemble as step 1~4, then load a R4 holder to the end,
pending crimping
;
(6),
保持步骤(
3
)R4 holder与线缆的相对位置, 按照步骤5～9,压接线束, 完成线束另一端组装;
hold
relative position of R4 holder & cable as in step(
3
),
follow step5~9, crimp cable, complete
connector assemble of this end;
(7),
将步骤(4)记录的角度/位置写入作业指引, 后续即按该旋转角度操作, 进行批量压接/组装.
record
the R4 rotation angle/position in step(4), form an operation instruction for mass assembly.
PDU or
load负载
front view
正视图
Left view
左视图
(2),
取1pcs合金外壳, 将其开口对准并插入(PDU或负载的)插座, 放置待用;
take an alloy shell, align its
open with receptacle(on PDU or load panel), plug in, put it aside;
anti-rotation chamfers face ceiling & ground.
alloy shell
合金外壳
Receptacle
插座
注意
:
如线束待组装的另一端
未
采用止转
R4
端子
,
请忽略以下步骤
;
否则
,
请严格按以下步骤实施线束另一端的组
装 ！
If the other end to be assembled doesn’t adopt R4 holder with anti-rotation chamfer, then
ignore following steps, or please strictly follow following steps to assemble the other end!
R4 holder
receptacle fixed on
load or
PDU
插座
Plug in to
engage the
two
插入
HVIL align
高
压互锁位对齐
anti-rotation
chamfer
止转切面
vertical yellow line is
the pos link line
.
黄竖
线为两
/
三芯中心连线
.
2/3pos PowerLok 直头组装式插头安装规范(屏蔽款)
2/3pos PowerLok 180D Plug Assembly Specification(shielded
)
③
SS ring1
②
Rubber ring
①
end cap
⑤
R4 holder with anti-rotation
chamfer 带止转切面的R4端子.
④
SS ring1
