Amkus IC700 Скачать руководство пользователя страница 13

Страница: 13 / 20

©Copyright AMKUS Rescue Systems 2020-2021

LAI-004 February 3, 2021 Rev00

6.5 CONTROL VALVE ACTUATOR

The control valve actuator has three positions, OPEN, OFF, and CLOSE. The control valve actuator includes a deadman safety feature

which returns the control valve actuator to the OFF position (neutral) when released. When the control valve is in the OFF position, the

tool movement stops, and holds position and load. The control valve actuator controls the motor and hydraulic pump. Electronics within

the tool prevent electrical overload during operation.
Verify operation of control valve actuator by checking to see it returns automatically to the neutral position when released.

7.0 OPERATION
7.1 BATTERY CHARGE STATUS

Check the battery charge status using the indicator lights on the battery by pushing the status button on the battery.

Figure 7.1

7.2 WHEN TO CHANGE THE BATTERY

ION tools keep power ON until turned off, or after 20 minutes of inactivity. The battery management system maintains power until the

battery is drained. Push the status button on the battery to check the battery status. The indicator light bars display the battery’s charge

status.
Change the battery if the battery no longer continuously operates the tool, there is one bar left on the battery charge indicator, or the

Status LED indicates “red” for low battery.

7.3 STORAGE RECOMMENDATIONS

1. The best storage place is cool and dry, away from direct sunlight and excess heat or cold.

2. For long storage, it is recommended to store a fully charged battery pack in a cool dry place out of the tool and charger for optimal

results.

3. If the tool is exposed to water, remove the battery. Allow the battery and tool to dry before storage or use.

7.4 STATUS LED

During tool operation, the brightness of the LED will adjust to indicate to the user the amount of power the tool is currently using to

operate. The brighter the LED the more power being applied to cutting or spreading. The LED is also used to communicate status of

important tool conditions to the operator. Error codes will not prevent the tool from operating. The codes are intended to alert the

operator of a potentially harmful condition.

LED COLOR

STATUS MESSAGE

Green

Battery Good

Red

Battery Low

Yellow

Tool in Error

• Temperature is over 113°F (45°C)

• Temperature is under 3°F (-16°C)

• Actuator ON, motor not running

• Actuator NOT ON, motor running

Flashing Red

Battery Fault

Содержание IC700





















Результаты поиска

Содержание IC700

Отзывы:

Похожие инструкции для IC700

Бренды по названию

Популярные бренды

Amkus IC700, Инструкции по безопасной эксплуатации и техническому обслуживанию

Результаты поиска

Содержание IC700

Отзывы:

Похожие инструкции для IC700

Бренды по названию

Популярные бренды