background image

©Copyright AMKUS Rescue Systems, Inc. 2010 - 2019 

LAS-002 August 19, 2019 Rev03

8

6.2 EXTENDED REACH SPREADER TIPS

The AMK-30CRT spreaders have removable tips. AMK-30CX spreaders don’t have removable tips, but they are upgradable.  To 
remove the spreader tip, use a thumb and fi nger to depress the spring loaded tip pins, and remove the tips. To re-install the spreader 
tip, slide the tip back into place. Be sure that both pins return fully to their original positions. 
The reach and versatility of the spreader can be increased by using the Extended Reach Tips (ERT). ERT tips are interchangeable 
with the standard tips. 

GATOR TIP

ERT TIP

COMBO TIP 1

COMBO TIP 2

Figure 6.2a

Figure 6.2b

6.3 CHAIN USE

Chain kits are available for spreaders with removable tips.

WARNING

Transport chain is NOT rated for overhead lifting. Injury or death may occur from improper chain 
use. Observe chain safety guidelines established by the Authority Having Jurisdiction.

Setup and operation of both chain kits are the same:
• Secure chains around the load removing slack using grab hooks to 

latch fully across the chain (tip of hook must not to be inserted into 
holes of the chain link)

• Remove slack in the chain using quick adjust links.
• Tension the chain slightly and check to see that the connections are 

stable and safe

• Activate the control valve to close the arms and draw the load

Figure 6.3a

Chain rating; 3/8” grade 70 Transport chain, working load limit 6600 lbs (2994 kg)

RELEASE

LOCK

 K-CHAIN24-30

Figure 6.3b

Figure 6.3c

Содержание AMK-30CRT Series













Отзывы: