Amit APT4015A Скачать руководство пользователя страница 6

APT4015A(

X

apt4015ax_g_en_100 

6/49 

Introduction 

APT4015A(x)

  is  a

 

panel  computer  built  on  a  PC  platform.  It  is  intended  to  be 

built-in into switchboard front panel. 
 
The panel computer 

APT4015A(x) 

contains the main processor module with the 

processor Intel

®

 Atom

™ 

(hereinafter referred to as the main CPU). 

 

  CPU Intel

® 

Atom

 E3815, Single core, 1.46 GHz 

  2 GB DDR3L RAM 

  4 GB SATA SLC eMMC 

 

TFT LCD 15,6" interface (1366 × 768), LED backlight 

  Resistive touch panel 

 

1× slot miniPCIe for mSATA 

  1

× RS485 interface (galvanic isolation) 

 

1× RS232 interface without galvanic isolation 

 

2× USB with A-type USB connector 

 

2× Ethernet interface 1 Gbps, connector RJ45 

  Nominal power supply voltage 24 V DC  

 
The panel computer is designed to work within the whole operating temperature 
range right after startup, without the need of tempering. 

To  avoid  damage  of  electronics  the  computer  switches  automatically  off 
whenever critical temperature inside the system is reached. 

On panel computer can run most of available operating systems. Please contact 
AMiT  technical  support  for  information  about  current  OS  versions  and  support 
for the OS launch. 
 

Properties 

Содержание APT4015A


















































Отзывы: