Amico Gooseneck Скачать руководство пользователя страница 7

Страница: 7 / 20

www.amico.com

NOTE:

HEAD-HW KIT

contains the hardware necessary for this section.

NOTE:

The GOOSENECK may have come with pre-installed power cable for the tablet OR you may need to run a

power-supply wire through the

GOOSENECK

. Wires at the bottom of the

GOOSENECK

should be fed

through the cable channel (notch in

GOOSENECK

ROLL STAND POST ADAPTER

Section 3: Assembly

NOTE: GOOSENECK-HW KIT

contains the hardware necessary for this section.

NOTE:

Always align the

GOOSENECK

ROLL STAND POST ADAPTER

(small notch at top of adapter) cable channel

with

GOOSENECK

mount plate slot cut as shown below.

2. Use the #2 Phillips head screwdriver, place the

GOOSENECK

with

TABLET MOUNT

on top of the

GOOSENECK

ROLL

STAND POST ADAPTER MOUNT

and secure with 3x

GOOSENECK HW-KIT SCREWS

(Figure 2)

Figure 2

TABLET HEAD MOUNT

[X-MON-DISK-LNG]

X-GOSNECK-NP SCREWS

[H-FHMS-632-38-P]

NON POWERED GOOSENECK

[

X-GOSNECK-NP]

TABLET MOUNT

[X-TB-MNT-HG]

DETAIL A

Always Align cable channel

with mounting plate slot

TABLET MOUNT

[X-TB-MNT-HG]

X-GOSNECK-NP SCREWS

[H-FHMS-632-38-P]

TABLET HEAD MOUNT

[X-MON-DISK-LNG]

NON POWERED GOOSENECK

[X-GOSNECK-NP]

TABLET HEAD MOUNT

[X-MON-DISK-LNG]

X-GOSNECK-NP SCREWS

[H-FHMS-632-38-P]

NON POWERED GOOSENECK

[

X-GOSNECK-NP]

TABLET MOUNT

[X-TB-MNT-HG]

DETAIL A

Always Align cable channel

with mounting plate slot

Always align cable

channel with

mounting plate slot

DETAIL A

Содержание Gooseneck





















Результаты поиска

Содержание Gooseneck

Отзывы:

Похожие инструкции для Gooseneck

Бренды по названию

Популярные бренды

Amico Gooseneck, Руководство по сборке

Результаты поиска

Содержание Gooseneck

Отзывы:

Похожие инструкции для Gooseneck

Бренды по названию

Популярные бренды