background image

ELECTRIC RETRACTORS

Page 

7

 of 

1

2

ELECTRICAL RETRACTORS

 

The Easy Pull only secures the front of the 
wheelchair. The wheelchair must be 
secured
with additional belts at the rear. The 
wheelchair passenger must wear an 
occupant
securement. Proper use also includes 
strict adherence to the information given in 
this
manual.
WARNING!
• Only use the Easy Pull for the purpose for 
which it was intended: wheelchair mobility.
• Always adhere to information given in this 
user and installation manual.
• Do not use the Easy Pull for any other 
purposes, particularly those given in
Section 1.2. These are deemed to be 
improper use.
Page

Recommended distances are based on common wheelchair sizes. 
Exceptionally large or small wheelchairs may require anchorage spacing 
that differs from our recommendations.  Consider optimal tie-down angles 
to determine exact placement of floor anchorages

.

 (

See Figure 1 below)

This product is designed for use as a front tie-down ONLY and is operated 
using a switched and fused 12v DC power supply. 

The following are the recommended best installation practices and distances 
(center-to-center) between floor anchorages.

1)

Ensure the vehicle is parked on a suitable firm and level surface, taking care to not have

 

to

o

 great of an incline and with the parking brake applied.

2)

Open the access door and position ramp.

3)

Position the wheelchair at the bottom of the ramp straight on and apply the

wheelchair brake so that it is secure while attaching the Electric Retractor hooks / loops.

4)

Turn on power to 

the 

Electric Retractors. This will unlock them and allow the webbing to

 

be pulled out.

5) H

old attachment device (hook / loop) and pull webbing out of the vehicle to

 w

heelchair.

6)

Turn retractors power OFF before pushing wheelchair up the ramp. Powering off will

 

lock

 

the retractors and stop wheelchair from backing up on the ramp. It is recommended

 

to

 

position the wheelchair approximately 8" away from the retractors, if possible.

7)

Apply rear tiedowns onto the wheelchair as trained. Apply occupant securement

(lap / shoulder belts) as trained. Fold ramp and close access door.

Содержание Electric Retractor













Отзывы: