Ametek ORTEC MOBIUS-B Скачать руководство пользователя страница 4

PROPERTY OF AMETEK, INC. 

 ORTEC

®

 

ORTEC

 

®

 

MÖBIUS™ Recycler HPGe Detector Cooling System 

805709F / 1115 

iv

 

 

ADDITIONAL WARRANTY AND SAFETY NOTICES 

There are no serviceable parts in or on the MÖBIUS except those specified in this manual, e.g., the mains power cord, 
fuses,  and  filter.  Opening  the  rear  panel  or  otherwise  accessing  the  interior  components,  attempting  to  detach  the 
level monitor or remote status display leads, or performing operations other than those described in this manual (e.g., 
inserting/removing  the  mechanical  cooler’s  protective  foam  block,  adding/removing  liquid  nitrogen,  and 
inserting/withdrawing detector crystostats into/from the dewar) may void your warranty. 

Using this equipment in a manner not specified in this manual may impair the protection the equipment provides. 

Changes to valving, tubing, or other components of the MÖBIUS system can result in damage to equipment, injury, 
or  death.  Modifications  to  any  system  components  must  be  made  in  consultation  with  ORTEC  technical  support 
personnel and authorized in writing in advance of such modifications. 

 

 

 

SAFETY INSTRUCTIONS AND SYMBOLS 

This manual contains up to three levels of safety instructions that must be observed in order to avoid personal injury 
and/or damage to equipment or other property. These are: 

DANGER

 

Indicates  a  hazard  that  could  result  in  death  or  serious  bodily  harm  if  the  safety  instruction  is  not 
observed. 

WARNING

  Indicates a hazard that could result in bodily harm if the safety instruction is not observed. 

CAUTION

 

Indicates a hazard that could result in property damage if the safety instruction is not observed. 

Please read all  safety instructions carefully  and make sure you understand them fully  before attempting to use this 
product. 

In addition, the following symbol might appear on the product: 

ATTENTION  –  Consult  the  manual  in  all  cases  where  this  symbol  is  marked  in  order  to 
determine  the  nature  of  the  potential  hazards  and  any  actions  that  must  be  taken  to  avoid 
them 
 
DANGER – Hazardous voltage 
 
 
Protective earth (ground) terminal 

 

Please read all  safety instructions carefully  and make sure you understand them fully  before attempting to use this 
product. 

 

Содержание ORTEC MOBIUS-B





























Отзывы: