Qi Wireless Charger Owners Manual
PM1001QIPCB
FCC Statement
This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Note: Modifications to this product will void the user’s authority to operate this equipment.
Limited Warranty
Under normal use and conditions, AmerTac provides to the original
purchaser of this product a one year limited express warranty that is set
forth in the Limited Warranty stated in full at www.amertac.com/warranties.
The Limited Warranty is in lieu of all other express or implied warranties or
liabilities subject to the exceptions explained fully in the Limited Warranty
on the website.
IMPORTANT SAFETY INFORMATION:
IMPORTANT SAFETY INSTRUCTIONS
For use with 120V, 60Hz electrical power supply only. Not to be
used with travel converters.
SAVE THESE INSTRUCTIONS
Read and understand all of these instructions before using this
product. Read all instructions and warnings prior to using this
product. Improper use of this product may result in product
damage, excess heat, toxic fumes, fire or explosion, for
which damages you (“Purchaser”), and not AmerTac
(“Manufacturer”) are responsible.
Keep these instructions in a safe place for future reference.
SPECIFICATIONS
Model: PM1001QIPCB
Product Standard: Qi
TX Input: DC5V/1.5A
RX Output: DC5V/1000mA Max
Working Frequency: 110-205KHz
Size: 6.2” (158mm) L x 3.3” (85mm) W x 0.4” (9mm) D
Compatibility: Qi-enabled devices, iPhone 8, iPhone 8 Plus, iPhone X or later,
Samsung Galaxy S8, S8 Plus/S8+, S7, S7 Edge, Note 5 & S6 Edge Plus, Samsung
Galaxy S6, S6 Edge Nexus 5, etc., Nokia Lumia 920, LG Nexus 5/4/7, Samsung
Galaxy S3/S4/S5, Note 3/Note2 with receiver card or receiver case, ect.
CHARGING YOUR WIRELESS DEVICE
• Connect the Power Supply Cable to Qi Charging Pad and to
any 5V USB power supply (not included). Be sure connections
are secure.
• You will see a blue LED light for about 3 seconds then a green
light will show through charging pad at the Light Indicator Area
noted in the “What’s Included” section of this manual. You may
also hear a tone from your device indicating it is connected and
charging properly.
• Place your Qi compatible wireless device on charging pad.
When the device is charging, the LED light color will change from
green to blue. When the device is removed from the charging
pad the LED will turn back to green. Your device may feel warm
to the touch as it is charging or if it remains on the charger when
fully charged. This is normal. The device should be removed
when fully charged as indicated on your device.
• Remove device when fully charged. Your device may feel warm
to the touch as it is charging. This is normal.
250 Boulder Dr.
Breinigsville, PA 18031
610-336-1330
www.amertac.com
Made in China /
Fabriqué en Chine /
Fabricado en China
© 2018 AmerTac™
I18-0025-A
Zenith is a registered trademark and used under license to AmerTac
Zenith est une marque de commerce déposée et utilisée sous licence par AmerTac.
Zenith es una marca registrada y se utiliza bajo licencia por AmerTac
WARNING
• This product may represent a possible shock or fire hazard if
improperly installed or attached in any way. To prevent
overheating and electrical shock do not operate in small
enclosed spaces.
• For questions or instructions for the various ways to charge using
this device refer to the “Charging Your Wireless Device” section
of this manual.
• Do not store device in high-temperature environment, including
heat caused by intense sunlight or other forms of heat. Do not
place device in fire or other excessively hot environments.
• Do not operate in wet locations or immerse in water.
• Do not disassemble this device or attempt to re-purpose or
modify it in any manner.
• Do not attempt to replace any part of this device.
• Keep away from devices with magnetic stripe or chip (ID cards,
bank cards, etc.).
• Keep at least 22 cm / 9 in away from medical implants to avoid
interference.
• Remove charger from power when not in use.
• Do not charge with any material or object between charger
and device.
• Do not place any metallic or aluminum material on charging
pad.
• Do not use broken adaptors, or cables.
• Do not squeeze, bend or scratch the inductive charger.
• If this device is accessible to or may be used by a minor,
purchasing adult agrees to be solely responsible for providing
supervision, instruction, and warnings. Purchaser agrees to
defend, indemnify, and hold Manufacturer harmless for any
claims or damages arising from unintended use or misuse by a
minor.
• All products have gone through a thorough quality assurance
inspection. If you find that your device is excessively hot, is
emitting odor, is deformed, abraded, cut or is experiencing or
demonstrating an abnormal phenomenon, immediately stop all
product use and contact Manufacturer.
• To comply with FCC RF exposure compliance requirements, the
wireless charging base must be used with a separation distance
of at least 10cm/ 4 in from all persons.
What’s Included
1. Power Supply Cable
2. Charging area
3. Light indicator Area
4. Owner’s Manual
QI™ COMPATIBILITY
This product complies with the Qi wireless charging standard
set by the WPC. It can charge any device marked with the
Qi logo,
NOTE: The Qi symbol is a trademark of the Wireless Power Consortium
1
4
2
3
