background image

Ameritron AL-572 

Instruction Manual 

13 

TECHNICAL ASSISTANCE 

Technical assistance is available during normal central standard time business hours on 
weekdays.  Customer service is more effective when our technicians are provided the following 
information: 

1.  Model and serial number 
2.  Date of purchase and dealer 
3.  An accurate description of the problem 

Meter readings at all stages of the tuning procedure are very important along with a complete 
description of the other equipment used with our product. 

Written assistance is also available.  Due to time delays in processing mail, please allow at least 
three weeks for a written reply.  For service or written correspondence, use the following address: 

AMERITRON 
116 Willow Rd. 
Starkville, MS.  39759 
Telephone:  (662) 323-8211 
FAX:  (662) 323-6551 

Note:

  Service history has clearly shown that most problems are operating or installation 

errors, rather than equipment failures.  Most problems can be resolved over the 
telephone.  Please contact our staff before 
shipping parts or equipment to us. 

The packing materials used to ship this amplifier were specially designed to prevent shipping 
damage.  The original packing materials should be used to ship this amplifier.  Replacement 
packing materials may be purchased from Ameritron if original packing materials are unavailable 
or damaged. 

CAUTION: Never ship this amplifier with the tube installed. 

Ameritron will not be responsible for shipping damage 
caused by improper packing. 

 

N

OTES

 

 

 

 

 

 

 

 

 

Содержание AL-572







































Отзывы: