AmeriGlide Hercules II Hybrid Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 34

background image

10

HERCULES II HYBRID INSTALLATION GUIDE

(800) 580-0831

www.AmeriGlide.com

AmeriGlide

PROCEDURE

Install the Upper Rail Assembly on top of the Lower Rail Assembly.

INSTALL

1. Align and place the Upper Rail Assembly on top of the Lower Rail Assembly.
2. Ensure that the bottom of the Upper Rails rest flush on top of the Lower Rail

Assembly.

3. Secure the Upper Rail Assembly to the Lower Rail Assembly using 2 Hex Bolts

(1/4”-

20 X 1”)

on each side.

4. Attach the Upper Rail Assembly to the Supporting Wall using a Lag Screw

(#14-4”)

on each side.

ONLY USE THE PRE-DRILLED HOLES FOUND ON THE RAIL AND THE

HORIZONTAL BRACING.

3. INSTALL UPPER RAIL ASSEMBLY

Lag Screw

(#14-4”)

Horizontal Bracing

Horizontal Bracing

Hex Bolts

(1/4-20 by 1”)

Rail

Lower and Upper Rail Assembly.

Lower Rail Assembly

ALWAYS USE THE PRE-DRILLED HOLES THAT

INTERSECT THE RAIL AND THE HORIZONTAL

BRACING WHEN MOUNTING RAIL ASSEMBLY

TO SUPPORTING WALL.

WARNING

«
...
8
9
10
11
12
...
»

Содержание Hercules II Hybrid



































Отзывы:

Нет отзывов

Похожие инструкции для Hercules II Hybrid

Бренд: WAREMA Страницы: 4

Бренд: Abicor Binzel Страницы: 160

Pulstronic 2011 Mod. 313

Бренд: Suevia Страницы: 40

Бренд: Digitrax Страницы: 8

ProcessLogix 1757-SRM

Бренд: Allen-Bradley Страницы: 36

THERMASGARD 9112

Бренд: S+S Regeltechnik Страницы: 48

Бренд: GCAN Страницы: 12

Бренд: Liko Страницы: 37

Бренд: WIA Страницы: 24

Invertec V160-T

Бренд: Lincoln Electric Страницы: 4

I/O SYSTEM 750 750-671

Бренд: WAGO Страницы: 256

Panelovn Zigbee

Бренд: Namron Страницы: 11

Бренд: M-system Страницы: 6

Бренд: Marson Страницы: 50

Бренд: WeldKing Страницы: 38

Бренд: Lincoln Electric Страницы: 56

Бренд: iSMA Страницы: 107

Бренд: Honeywell Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды