background image

 

 

Americana Outdoors, Inc.

1

Illini Installation Guide

 

 

Before You Begin:

 

• 

Consult your local building department for any required permits

 

 

You may be required to obtain a building permit for this structure. Contact your local building

 

 

department for details.

 

• 

Read instructions thoroughly

 

 

Please read all instructions and notes carefully prior to assembly. Americana is not responsible

 

 

for replacing parts lost or damaged due to incorrect assembly.

 

• 

Check for all parts

 

 

Use the Parts and Hardware List to check for any missing parts. To prevent scratching of painted

 

 

materials, place on a tarp or other protective material.

 

• 

Prepare surrounding area

 

 

Remove any obstructions around shelter location. Shelter installation should be scheduled after

 

 

all concrete and masonry work in the surrounding area is completed.

 

• 

Assistance is required during entire assembly.

 

 CAUTION

 

• 

Proper site preparation is required.

 

• 

Standard shade structure design does not include additional loads such as hanging heavy plants, 
swings, or other objects.

 

• 

DO NOT stand or sit on the shade structure roof.

 

• 

Repair or replace broken parts immediately.

 

• 

This kit contains parts with metal edges. Please be careful when handling.

 

ILLINI SHELTER

 

INSTALLATION INSTRUCTIONS

 

Contact us at:

 

1

-

800

-

851

-

0865  or

 

www.americana.com

 

Содержание ILLINI
















Отзывы: