manualshive.com logo in svg

AMERICANA ALUMA-VENT, Руководство по установке

Поделиться
Скачать
AMERICANA ALUMA-VENT Скачать руководство пользователя страница 20

 

 

Americana Building Products               .

Optional Sheet C - Page 20

 

Aluma-Vent Installation Guide

 

STEP C3 

Mark (2) holes approximately 1-1/2” apart centered 
one side of C-channel bracket (O). Drill the holes 
using a 5/16” drill bit. 

Position the C-channel bracket (O) against the 
mounting surface and C-channel brace (N). Mark 
and drill the same hole pattern through the side of 
C-channel brace (N). 

Attach the bracket to the brace using (2) 1/4” x 3/4” 
bolts (FF) and 1/4” square nuts (GG). 

 

 

Depending on the 
drop of your awning, 
the brace may be cut 
at the wall to the 
proper angle.

 

STEP C4 

Attach C-channel bracket (O) to the mounting 
surface using (2) 1/4” diameter anchors suitable for 
your mounting surface. Pre-drill a pilot hole into the 
mounting surface using a 1/8” drill bit. 

NOTE: Awning must be attached to a solid 
structural support. DO NOT attach awning to 
sheathing, siding, flashing, or any other 
non-structural surface. 

C3 

C4 

OPTIONAL FIELD CUT 

Содержание ALUMA-VENT


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды