manualshive.com logo in svg

AMERICANA ALUMA-VENT, Руководство по установке

Поделиться
Скачать
AMERICANA ALUMA-VENT Скачать руководство пользователя страница 10

 

 

Americana Building Products               .

10

 

Aluma-Vent Installation Guide

 

STEP 10 

At this point, the awning may be lifted up and 
attached to the mounting surface. Anchors are not 
supplied with this kit. 3/16” diameter anchors 
suitable for your mounting surface are required. 
 

NOTE: Awning must be attached to a solid 
structural support. DO NOT attach awning to 
sheathing, siding, flashing, or any other 
non-structural surface. 

 
While using a level to keep flashing (E) plumb, 
attach to the mounting surface through the 
pre-drilled holes. Pre-drill a pilot hole into the 
mounting surface using a 1/8” drill bit before 
attaching anchors. 

STEP 11 

With only the top of the awning attached to the 
mounting surface, use a level to plumb sawtooth (B) 
and louvers (H). Looking at the side of the awning, 
the louvers should be parallel to the mounting 
surface. Looking at the front of the awning, the 
louvers should appear straight up and down. 

With the awning properly aligned, attach mounting 
bracket (G) to the mounting surface using 3/16” 
diameter anchor, purchased separately. Then be 
sure to tighten the #8 x 3/4” screws (AA) attached to 
mounting bracket (G). Pre-drill a pilot hole into the 
mounting surface using a 1/8” drill bit before 
attaching anchors. 

TIP: Align and attach one end of the awning 
before moving to the other side to avoid either 
side falling out of alignment. 

Once the awning is attached, if you need to 
move runner (C) to avoid an out-swinging door 
or window, remove #14 x 3/4” screws (DD), 
re-position the runner, then re-attach screws. 

10 

11 

Содержание ALUMA-VENT


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды