background image

39

limited warranty

American Water Heater, the warrantor, extends the following LIMITED WARRANTY to the owner of this water heater.

THE TANK

1. 
If the glass-lined tank in this water heater shall prove upon examination by the warrantor to have leaked due to natural corrosion from potable water 

therein, during the first THREE years after initial installation, the warrantor will supply a replacement tank less burner and controls or a complete 

new American water heater of equivalent size and current model at the warrantor’s option. Some government agencies are requiring energy efficient 

standards for water heaters. In the event regulations prohibit sale of a model of equivalent size and construction, American will provide a model which 

complies with the regulations of your area, in which case the consumer will be charged the difference in price between the like replacement and the 

energy efficient model required. The warranty on the replacement water heater will be limited to the unexpired term of the original warranty.

ALL OTHER PARTS

2. 
If within ONE year after initial installation of this water heater, any part or portion shall prove upon examination by the warrantor to be defective in 

material or workmanship, the warrantor will repair or replace such part or portion at its option.

CONDITIONS AND EXCEPTIONS

3. 
This warranty shall apply only when the water heater is installed in accordance with local plumbing and building codes, ordinances and regulations, 

the printed instructions provided with it and good industry practices.  In addition, a temperature and pressure relief valve, certified by CSA and 

approved by the American Society of Mechanical Engineers, must have been installed.

  a. This warranty shall apply only when the water heater is:

    (1) owned by the original purchaser;

    (2) used at temperatures not exceeding the maximum setting of its thermostat;

    (3) used at water pressure not exceeding the working pressure shown on the heater;

    (4) 

used when operated free of the damaging effects of uncontrolled water hammer;

    (5) used when filled with potable water, free to circulate at all times; 

    (6) used in a non-corrosive and non-contaminated atmosphere;

    (7) used with factory approved anode(s) installed;

    (8) in its original installation location;

    (9) in the United States, its territories or possessions, and Canada;

    (10) sized in accordance with proper sizing techniques for commercial water heaters;

    (11) bearing a rating plate which has not been altered, defaced or removed except as required by the warrantor;

    (12) fired at the factory rated input using the fuel stated on the rating plate;

    (13) maintained in accordance with the instructions printed in the manual included with the water heater.

  b. Any accident to the water heater, any misuse, abuse (including freezing) or alteration of it, any operation of it in a modified form, or any attempt 

to repair tank leaks will void this warranty.

  c. 

This warranty is void if a device acting as a backflow prevention device (check valves etc.) is installed in the cold water supply the heater is 

connected to, unless an effective method of controlling thermal expansion is also installed at the heater(s) and operational at all times.

 

    The temperature and pressure relief valve installed on the heater is not an acceptable method. 

SERVICE AND REPAIR EXPENSES

4. 
Under the limited warranty the warrantor will provide only a replacement water heater or part thereof.  The owner is responsible for all other costs. 

Such costs may include but are not limited to:

  a. Labor charges for service removal, repair or reinstallation of the water heater or any component part;

  b. Shipping, delivery, handling, and administrative charges for forwarding the new heater or replacement part from the nearest distributor and returning 

    the claimed defective heater or part to such distributor.

  c. All cost necessary or incidental for any material and/or permits required for installation of the replacement.

LIMITATIONS ON IMPLIED WARRANTIES

5. 

Implied warranties, including the warranty of merchantability imposed on the sale of this heater under state law are limited to one (1) year duration for 

the heater or any of its parts. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

CLAIM PROCEDURE

6. 

Any  claim  under  the  warranty  should  be  initiated  with  the  dealer  who  sold  the  water  heater,  or  with  any  other  dealer  handling  the  warrantor’s

 

products. If this is not practicable, the owner should contact:
 

American Water Heater

 

Product Service and Support

 

PO Box 1597, 500 Princeton Road

 

Johnson City, TN 37065

  a. The warrantor will only honor replacement with identical or similar water heater or parts thereof which are manufactured or distributed by the warrantor.

  b. Dealer replacements are made subject to in-warranty validation by warrantor.

DISCLAIMERS

7. 
NO OTHER EXPRESS WARRANTY HAS BEEN OR WILL BE MADE IN BEHALF OF THE WARRANTOR WITH RESPECT TO THE MERCHANTABILITY 

OF  THE  HEATER  OR THE INSTALLATION, OPERATION, REPAIR OR REPLACEMENT OF THE WATER  HEATER. THE WARRANTOR SHALL 

NOT BE RESPONSIBLE FOR WATER DAMAGE, LOSS OF USE OF THE UNIT, INCONVENIENCE, LOSS OR DAMAGE TO PERSONAL PROPERTY 

OR OTHER CONSEQUENTIAL DAMAGE. THE WARRANTOR SHALL NOT BE LIABLE BY VIRTUE OF THIS WARRANTY OR OTHERWISE FOR 

DAMAGE TO ANY PERSONS OR PROPERTY, WHETHER DIRECT OR INDIRECT, AND WHETHER ARISING IN CONTRACT OR TORT.

  a. Some states do not allow the exclusion or limitation of the incidental or consequential damage, so the above limitations or exclusions may not apply to you.

  b. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Fill in the following for your own reference. Keep it

. Registration is not a condition of warranty. The model and serial number are found on the heater’s rating plate.

Date Installed ____________________ Model No. ______________________________________Serial No.  ______________________________

Dealer’s Name

 ___________________________________________________________ Phone No. ____________________________________

Dealer’s Address

 _____________________________________________ City and State _______________________ Zip Code _______________

fIll In warrantY and Keep for future reference.

Содержание vG6250t76nv









































Отзывы: