background image

74

American Water Heater Company, the warrantor, extends the following LIMITED WARRANTY to the owner of this water heater.
1. 

THE TANk

If the glass-lined tank in this water heater shall prove upon examination by the warrantor to have leaked due to natural corrosion from potable water therein, 

during the first THREE years after initial installation, the warrantor will supply a replacement tank less burner and controls or a complete new American water 

heater of equivalent size and current model at the warrantor's option. Some government agencies are requiring energy efficient standards for water heaters. In 

the event regulations prohibit sale of a model of equivalent size and construction,  American Water Heater Company will provide a model which complies with 

the regulations of your area, in which case the consumer will be charged the difference in price between the like replacement and the energy efficient model 

required. The warranty on the replacement water heater will be limited to the unexpired term of the original warranty.

2. 

ALL OTHER PARTS

If within ONE year after initial installation of this water heater, any part or portion shall prove upon examination by the warrantor to be defective in material or 

workmanship, the warrantor will repair or replace such part or portion at its option.

3. 

CONDITIONS AND ExCEPTIONS

This warranty shall apply only when the water heater is installed in accordance with local plumbing and building codes, ordinances and regulations, the printed 

instructions provided with it and good industry practices.  In addition, a temperature and pressure relief valve, certified by CSA and approved by the American 

Society of Mechanical Engineers, must have been installed.

  a. This warranty shall apply only when the water heater is:

    (1) owned by the original purchaser;

    (2) used at temperatures not exceeding the maximum setting of its thermostat;

    (3) used at water pressure not exceeding the working pressure shown on the heater;

   (4) 

used when operated free of the damaging effects of uncontrolled water hammer;

    (5) used when filled with potable water, free to circulate at all times; 

    (6) used in a non-corrosive and non-contaminated atmosphere;

    (7) used with factory approved anode(s) installed;

    (8) in its original installation location;

    (9) in the United States, its territories or possessions, and Canada;

    (10) sized in accordance with proper sizing techniques for commercial water heaters;

    (11) bearing a rating plate which has not been altered, defaced or removed except as required by the warrantor;

    (12) fired at the factory rated input using the fuel stated on the rating plate;

    (13) maintained in accordance with the instructions printed in the manual included with the water heater.

  b. Any accident to the water heater, any misuse, abuse (including freezing) or alteration of it, any operation of it in a modified form, or any attempt 

to repair tank leaks will void this warranty.

  c. This warranty is void if a device acting as a backflow prevention device (check valves etc.) is installed in the cold water supply the heater is 

connected to, unless an effective method of controlling thermal expansion is also installed at the heater(s) and operational at all times.

 

    The temperature and pressure relief valve installed on the heater is 

not

 an acceptable method.

 

4. 

SERvICE AND REPAIR ExPENSES

Under the limited warranty the warrantor will provide only a replacement water heater or part thereof.  The owner is responsible for all other costs. Such costs 

may include but are not limited to:

  a. Labor charges for service removal, repair or reinstallation of the water heater or any component part;

  b. Shipping, delivery, handling, and administrative charges for forwarding the new heater or replacement part from the nearest distributor and returning

 

    the claimed defective heater or part to such distributor.

  c. All cost necessary or incidental for any material and/or permits required for installation of the replacement.
5. 

LImITATIONS ON ImPLIED WARRANTIES

Implied warranties, including the warranty of merchantability imposed on the sale of this heater under state law are limited to one (1) year duration for the heater 

or any of its parts. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

6. 

CLAIm PROCEDuRE

Any  claim  under  the  warranty  should  be  initiated  with  the  dealer  who  sold  the  water  heater,  or  with  any  other  dealer  handling  the  warrantor’s

 

products. If this is not practicable, the owner should contact:

      

 

U.S. Customers

 

 

   

 

 

American Water Heater Company 

 

   

 

 

PO Box 1597, 500 Princeton Road 

 

   

 

 

Johnson City, TN 37605 

 

   

 

 

Telephone: 1- (800) 456-9805 

  a. The warrantor will only honor replacement with identical or similar water heater or parts thereof which are manufactured or distributed by the warrantor.

  b. Dealer replacements are made subject to in-warranty validation by warrantor.
7. 

DISCLAImERS

NO OTHER ExPRESS WARRANTy HAS bEEN OR WILL bE mADE IN bEHALF OF THE WARRANTOR WITH RESPECT TO THE mERCHANTAbILITy 

OF  THE  HEATER  OR THE INSTALLATION, OPERATION, REPAIR OR REPLACEMENT OF THE WATER  HEATER. THE WARRANTOR SHALL NOT BE 

RESPONSIbLE FOR WATER DAmAGE, LOSS OF uSE OF THE uNIT, INCONvENIENCE, LOSS OR DAmAGE TO PERSONAL PROPERTy OR OTHER 

CONSEQUENTIAL DAMAGE. THE WARRANTOR SHALL NOT BE LIABLE BY VIRTUE OF THIS WARRANTY OR OTHERWISE FOR DAMAGE TO ANY 

PERSONS OR PROPERTY, WHETHER DIRECT OR INDIRECT, AND WHETHER ARISING IN CONTRACT OR TORT.

  a. Some states do not allow the exclusion or limitation of the incidental or consequential damage, so the above limitations or exclusions may not apply to you.

  b. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Fill in the following for your own reference.  

keep it

.  Registration is not a condition of warranty. The model and serial number are found on the heater’s rating plate.

Date Installed________________________Model No.____________________________________________Serial No._________________________________________
Dealer’s Name

 

_____________________________________________________________________Phone No.________________________________________________

Dealer’s Address__________________________________________________City and State________________________________________Zip Code________________

fill in warranty and keep for future reference.

limited warranty

Содержание (A)HCG3 130T 300













































































Отзывы: