American Water Heater (A)HCG3 130T 300 Скачать руководство пользователя страница 6

Страница: 6 / 76

Thank You for purchasing this water heater. Properly installed

and maintained, it should give you years of trouble free service.

abbreViations used

Abbreviations found in this Instruction Manual include :

•  ANSI - American National Standards Institute
•  ASME - American Society of Mechanical Engineers
•  GAMA - Gas Appliance Manufacturer’s Association
•  NEC - National Electrical Code
•  NFPA - National Fire Protection Association
•  UL - Underwriters Laboratory
•  CSA - Canadian Standards Association

Qualifications

Qualified installer or serVice agency

Installation and service of this water heater requires ability

equivalent to that of a Qualified Agency (as defined by ANSI

below) in the field involved. Installation skills such as plumbing,

air supply, venting, gas supply and electrical supply are required

in addition to electrical testing skills when performing service.

ansi Z223.1 2006 sec. 3.3.83:

“Qualified Agency” - “Any

individual, firm, corporation or company that either in person or

through a representative is engaged in and is responsible for (a)

the installation, testing or replacement of gas piping or (b) the

connection, installation, testing, repair or servicing of appliances

and equipment; that is experienced in such work; that is familiar

with all precautions required; and that has complied with all the

requirements of the authority having jurisdiction.”
If you are not qualified (as defined by ANSI above) and licensed

or certified as required by the authority having jurisdiction

to perform a given task do not attempt to perform any of the

procedures described in this manual. If you do not understand

the instructions given in this manual do not attempt to perform

any procedures outlined in this manual.

preparing for the installation

1. Read the entire manual before attempting to install or operate

the water heater. Pay close attention to the General Safety

Information on page 4 and 5. If you don’t follow the

safety rules, the water heater may not operate safely. It could

cause property damage, injury and/or death.
This manual contains instructions for the installation,

operation, and maintenance of the water heater. It also

contains warnings throughout the manual that you must read

and be aware of. All warnings and all instructions are essential

to the proper operation of the water heater and your safety.
Detailed installation diagrams are also found in this manual.

These diagrams will serve to provide the installer with a

reference. It is essential that all venting, water piping, gas

piping and wiring be installed as shown.
Particular attention should be given to the installation

of thermometers at the locations indicated in the piping

introduction

diagrams as these are necessary for checking the operation

of the water heater.
The principal components of the water heater are identified

in Features And Components on page 7 in this manual.

Use this reference to locate and identify various components

on the water heater.
See the Installation Checklist and Troubleshooting on page

54. By using this checklist the user may be able to make

minor operational adjustments and avoid unnecessary

service calls. However, service and diagnostic procedures

should only be performed by a Qualified Service Agency.

note:

Costs to correct installation errors are not covered

under the limited warranty.

2. Be sure to turn off power when working on or near the

electrical system of the water heater. Never touch electrical

components with wet hands or when standing in water.

3. The installation must conform to all instructions contained in

this manual and the local code authority having jurisdiction.

These shall be carefully followed in all cases. Authorities

having jurisdiction should be consulted before installation

begins if there are any questions regarding compliance with

local, state or national codes.
In the absence of local codes, the installation must comply

with the current editions of the National Fuel Gas Code, ANSI

Z223.1/NFPA 54 and the National Electrical Code, NFPA 70 or

CAN/CSA-B149.1, the Natural Gas and Propane Installation

Code and CSA C22.1, the Canadian Electrical Code. All

documents are available from the Canadian Standards

Association, 8501 East Pleasant Valley Road, Cleveland, OH

44131. NFPA documents are also available from the National

Fire Protection Association, 1 Batterymarch Park, Quincy,

MA 02269.

4. If after reading this manual you have any questions or do

not understand any portion of the instructions, call the toll

free number on the back cover of this manual for technical

assistance. In order to expedite your request, please have the

full Model, Serial and Series number of the water heater you

are working with available for the technician. This information

is located on the water heater’s rating label.

5. Carefully plan the placement of the water heater. Examine

the location to ensure that it complies with the requirements

in Locating The Water Heater on page 11 and the Rough

In Dimensions on page 10.

6. For installation in California this water heater must be braced

or anchored to avoid falling or moving during an earthquake.

See instructions for correct installation procedures.

Instructions may be obtained from California Office of the

State Architect, 1102 Q Street, Suite 5100, Sacramento, CA

95811.

7. Massachusetts Code requires this water heater to be

installed in accordance with Massachusetts 248-CMR 2.00:

State Plumbing Code and 248-CMR 5. See Commonwealth

of Massachusetts on page 20.

Содержание (A)HCG3 130T 300













































































Результаты поиска

Содержание (A)HCG3 130T 300

Отзывы:

Похожие инструкции для (A)HCG3 130T 300

Бренды по названию

Популярные бренды

American Water Heater (A)HCG3 130T 300, Инструкция по эксплуатации

Результаты поиска

Содержание (A)HCG3 130T 300

Отзывы:

Похожие инструкции для (A)HCG3 130T 300

Бренды по названию

Популярные бренды