manualshive.com logo in svg

American Standard YHC033A, Установка, эксплуатация и обслуживание

Поделиться
Скачать
American Standard YHC033A Скачать руководство пользователя страница 4

4

General Information

Unit Nomenclature

Digit 1 - Product Type
Y = Packaged Gas/Elect

Digit 2 - Unit Efficiency Level
S = Standard
H = High

Digit 3 - Airflow Configuration
C = Convertible

Digit 4, 5, 6 - Cooling Capacity (MBH)

033 = 3 Ton
036 = 3 Ton
043 = 4 Ton
048 = 4 Ton
060 = 5 Ton
063 = 5 Ton
072 = 6 1/4 Ton
090 = 7 1/2 Ton (Single
Commpressor)
092 = 7 1/2 Ton (Dual Compressor)
102 = 8 1/2 Ton
120 = 10  Ton

Digit 7 - Major Design Sequence
A = First
E = R410A

Digit 8 - Electrical Characteristics

1 = 208-230/60/1
3 = 208-230/60/3
4 = 460/60/3
D = 380-415/50/3
K = 380/60/3
T = 200/50/3
W = 575/60/3

Digit 9 - Unit Control
R = Relia Tel
E = Electro-mechanical

Digit 10 - Heat Capacity
H =  High
M = Medium
L =  Low

X = Low, Stainless Steel Heat Exchanger
Y = Medium, Stainless Steel Heat

Exchanger

Z = High, Stainless Steel Heat Exchanger

Digit 11 - Minor Design Sequence

Digit 12, 13 - Service Digit Sequence

Digit 14 - Factory Installed Options
-Fresh Air Section
0 = No Fresh Air
A = Manual OA, 0 - 25%
B = Motorized OA, 0 - 50%
C = Economizer Dry Bulb
D = Economizer with
Barometric Relief
E = Economizer, Reference Enthalpy
F = Economizer, Reference Enthalpy,
with Barometric Relief
G = Economizer Comparative En-
thalpy
H = Economizer, Comparative En-
thalpy, with Barometric Relief

Digit 15 - Factory Installed Options
-Supply Fan
0 = Standard Drive
1 = Oversize Motor
2 = Option Belt Drive

Digit 16 - Factory Installed Options
-Hinged Service Access
0 = Standard Panels/Standard Filters
A =  Hinged Access Panels/Standard
         Filters
B = Standard Panels/2” Pleated Filters
C = Hinged Access Panels/2” Pleated
         Filters

Digit 17 - Factory Installed Options
-Condenser Coil Protection
0 = Standard
1 = Hail Guard
2 = Epoxy Coated Condenser Coil
3 = Epoxy Coated Condenser Coil
       and Hail Guard
4 = CompleteCoat Condenser Coil
5 = CompleteCoat Condenser Coil and
        Hail Guard

Digit 18 - Factory Installed Options
-Through The  Base
0 = Without Through The Base
      Connection
A = Through The Base Electrical
      Connection
B = Through The Base Gas
      Connection
C = Through The Base Electrical and
      Gas Connection

Digit 19 - Factory Installed Options
-Disconnect Switch/Circuit Breaker
0 = Without Disconnect Switch/Circuit
       Breaker/Phase Monitor
1 = Unit Mounted Non-Fused
       Disconnect Switch
2 = Unit Mounted Circuit Breaker
3 = Unit Mounted Phase Monitor
4 = Unit Mounted Phase Monitor and
      Unit Mounted Non-Fused
       Disconnect Switch
5 = Unit Mounted Phase Monitor and
       Unit Mounted Circuit Breaker

Digit 20 - Factory Installed Options
-Convenience Outlet
0 = Without Convenience Outlet
A = Convenience Outlet Unpowered
B = Convenience Outlet Powered

Digit 21 - Factory Installed Options
-Communications
0 = Without Communications Options
1 = Trane Communications Interface
2 = Lontalk Communications Interface
3 = Novar Communications Interface

Digit 22 - Factory Installed Options
-Refrigeration System
0 = Without Refrigeration System Op-
tion
A = Expansion Valve
B = Dehumidification Option

Digit 23 - Factory Installed Options
-Refrigeration Controls
0 = Without Refrigeration Controls
1 = High Pressure Control
2 = Frostat

TM

3 = Crankcase Heater
4 = High Pressure Control and Frostat
5 = High Pressure Control and
      Crankcase Heater
6 = Frostat and Crankcase Heater
7 = High Pressure Control, Frostat and
      Crankcase Heater

Digit 24 - Factory Installed Options
-Smoke Detector
0 = Without Smoke Detector
A = Return Air Smoke Detector
B = Supply Air Smoke Detector
C = Return and Supply Air Smoke
       Detector

Digit 25 - Factory Installed Options
-System Monitoring Controls
0 = Without Monitoring Controls
1 = Clogged Filter Switch
2 = Fan Failure Switch
3 = Discharge Air Sensing Tube
4 = Clogged Filter Switch and Fan
      Failure Switch
5 = Clogged Filter Switch and
       Discharge Air Sensing Tube
6 = Fan Failure Switch and
       Discharge Air Sensing Tube
7 = Clogged Filter Switch, Fan Failure
      Switch and
       Discharge Air Sensing Tube
8 = Novar Return Air Sensor

Содержание YHC033A

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды