American Standard QUENTIN 7440.801 Скачать руководство пользователя страница 1

Страница: 1 / 8

GROOVE IN
(FAUCET BASE)

MOUNTING

SURFACE

M 9 6 5 2 3 8

74 4 0 . 8 01

74 4 0 . 8 5 1

Certified to comply with ANSI A112.18.1

Adjustable Wrench

Screwdriver

Channel Locks

Recommended tools

Tubing Cutter

INSTALL FAUCET

Turn off hot and cold water
supplies before beginning.

CAUTION

Seat SEAL

(1)

into under side of ESCUTCHEON BASE

(2)

Feed FAUCET SUPPLIES

(3)

, MOUNTING STUD

(4)

and DRAIN

CABLE ASSEMBLY

(5)

through the mounting hole of lavatory or

mounting surface.

From below, push GASKET

(6)

with RETAINING WASHER

(7)

onto

MOUNTING STUD

(4)

. Secure Faucet with MOUNTING NUT

(8)

pushing faucet to back of sink, so SUPPLIES

(3)

rests against

mounting hole.

Adjust Faucet so that it is centered. Tighten MOUNTING NUT

(8)

to complete faucet mounting.

INSTALLATION

INSTRUCTIONS

WIDESPREAD LAVATORY
FAUCET with Speed Connect™ Drain

7440.801
7440.851

QUENTIN™

To ensure that your installation proceeds smoothly-please read these instructions carefully
before you begin.

Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only
on American Standard faucets.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

Speed Connect Drain*

• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.

Содержание QUENTIN 7440.801









Результаты поиска

Содержание QUENTIN 7440.801

Отзывы:

Похожие инструкции для QUENTIN 7440.801

Бренды по названию

Популярные бренды

American Standard QUENTIN 7440.801, Руководство по установке

Результаты поиска

Содержание QUENTIN 7440.801

Отзывы:

Похожие инструкции для QUENTIN 7440.801

Бренды по названию

Популярные бренды